ColdTi: Cryptocurrency Seed Storage (ColdTi: Cryptocurrency Seed Storage Stickered)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Not at all. There is still no substitute for punching.
We also offer a punch set option with this listing, in case you prefer that.
A few words were set with marker and then engraved after they were rewritten with an engraver Then I traced their lines with a My comfort level was excellent because it was so deep. The stamping I have not tried, as I have not even tried it.
Selected User Reviews For ColdTi: Cryptocurrency Seed Storage (ColdTi: Cryptocurrency Seed Storage Stickered)
Stacking the two plates together, they are each A 12 inch diameter).
The steps in their tutorial are best followed with a 3 to 5 pound steel mallet, not a carpenter's If you really hit the punch once, a nice, deep letter will follow. If you hit it a few times softly, you will damage it. Give it a loud whack once you've got it set up in the right spot and in the correct orientation. In the event that it gets damaged and falls apart, or if it accidentally gets opened and the letters fall out, it's game over! You'll have to work hard to remember them! A hammer and letter punches can only be used to make metal seed storage work. The letters must be pressed into a titanium plate using a hammer and letter punches. In the event of a house fire, what should you do? Depending on the amount of soot on the surface, the etching may be obscured. If you clean it and make it legible again, you may be able to recover it, but I wouldn't It would be my sole rule for imprinting the seed on the titanium plate using a punch. It is important to remember that CryptoSteel will cost you 6x as much as ColdTI, and it will not provide the necessary security against edge cases like those I've Buying smart is the key to success!.
It is for this reason that 4 stars are given rather than While I was stamping in the words, the plate started to curl from constant stamping, and then when I tried to unify both plates, my vise was too small to squeeze them so I had to use a vice to clamp them together so I could screw them However, don't get me wrong, the plates still curled quite a bit, and I still had to use a vise or pliers to push them together so the screws would go through.
In case you possess a Trezor or Ledger Nano, one of these is required. My stamping kit was an ImpressArt 3mm stamping kit (B01HUCPGGI), and it worked exactly as expected. Align the letters with a tape (mark hash marks with a pen) and strike the letters evenly and firmly. A mistake of striking the letter "h" and "b" incorrectly could lead to the top post of the letter being missed. Paper is not to be used. This is an indestructible product at a great price.
So far I have stamped the first of three that I ordered. The seed to number ratio is 39. Make sure everything is checked twice, triple checked, and stamped Do not pile on small hits, but rather one big one. It was on sale and I ordered an alphabetic stamp kit, a 3lb club hammer and a steel stamping block. There were a few characters that I had to line up and restamp due to off angles or strikes, but it is difficult to My plates came out perfectly flat and looks just like a tiny block that has been rubbed with steel wool or something. Over all, it looks like a tiny block that has been rubbed with steel wool or something. I see a lot of reviews where people's plates curl during the stamping process. I believe the ColdTi strip was not supported by a hard steel plate. For $17, I purchased a metal stamping block on Amazon. It was totally For $39 I think that this is an incredibly good deal, considering the fact that you get a high melt temperature metal, having your seed words screened, and a nice grid for seeds. It would be great if I could make the screw hardware pull tighter and if I had to nitpick, one of my screws came with part of the blacking missing. I used some Birchwood Casey Super Black and I like it. My purchase of these has been a good one.
There is no reason to complain. Instead of punching each letter, I used an electric engraver, and I was very satisfied with its results. The world is a better place because of me.
Approximately an hour was required for me to complete my seed words. It makes me feel good to have my seed words on something durable and easily hidden rather than on paper.
Here's a tip for new users I highly recommend this product. used Coke can as a test punch alignment to ensure the numbers were facing in the right direction, and I numbered the 0-32 until I had the right alignment The die was marked with a permanent marker with nine on it. In the case of the seed bip, I converted it into If you want to convert 0039 into a PDF file you will be able to search by number in the search bar to find words fast. I recommend turning off your internet connection before converting.
These two-pieces are everything they said they would be and no joke Even if the set isn't tested in a smelter, blast furnace, or near ground zero of an explosion, it will certainly survive My guess is that the information on these plates will be legible for the next 100 years if it is engraved on them. The next point I wish to raise is this In a word, this is the most ridiculously difficult surface to imprint upon without literally looking like the Hulk With a 5lb sledge, smash your typeset. The product is great, the price is fair, and it's definitely worth trying I was still caught up in the "Error" episode. Despite my dislike of Dremel tools, I think that may be the answer.