YANZEO Upper Fuser Roller for Brother HL3140 HL3150 HL3170 DCP9020 MFC9130 MFC9140 MFC9330 9340 Upper Fuser Roller 3170UFR

My first page came out well, but there were a few flecks probably left over from working on the printer while it was open. In the second page, the temperature was just right. There was a hot plastic smell when it first warmed, but it quickly dissipated. As a printer repair specialist, this is a quick and easy repair of medium complexity that I have done lots of in the past. Especially when handling the fuser heater and installing the roller under the fingers, as well as when attaching and removing this roller, you must be cautious The gear has been attached. The first time you deal with a laser printer repair, it is probably not the best thing to do if you have no experience.

Briggs Andrews

| Aug 02, 2020

Please see  " After watching Terry Jones' videos, I decided to buy this one because he specifically mentioned the cheap replicas, so I avoided those and got this one, who seems to have good reviews. Sadly, as soon as I printed each page, both had the same overheating problem. The seller was generous enough to send me another lower fuser roller after the first upper fuser roller melted, so thanks to them. I am not certain if what I got was a bad batch, but I assume it does not have the proper coating in the interior. Thanks for trying, but it couldn't be done. Please see attached the video I have taken of the issue I am seeing during publishing.

Jair Duffy

| Aug 18, 2020

It doesn't matter whether it's a knockdown Offered in this review, the fuser roller works perfectly in my Brother HL-200 fuser CDW 3170. As soon as I used it for the first time, there was no smell, and neither did there follow-ups. There is no difference in print quality between this one and the original. I do not know how long the system will last yet, so I cannot comment Yet the branded original was only able to last for about 6,000 pages, less than half the time it was advertised to last. As a result, I would expect this roller to last just as long, and at a considerably lower cost. You should carefully consider whether you want to take the risk of installing the device. I would recommend it to those who are mechanically inclined and may be interested in electronics, and it Nevertheless, the mechanism is extremely complex and fiddly, especially if the untrained hand is handling it Re-phrase your sentence as follows The roller is threaded over the heating element after the wires are plugged in. The sensor board on the fuser unit was inadvertently broken when I reconnected the fuser unit and plugged the thermistor connector back into the Rather than decipher it on the web), it required uninstalling, repairing, and reinstalling the board. Despite all the time I spent visiting the shop and trying to figure out how to do the repair, I had to spend another two hours to complete the

With the installation aside, I am a fan of this roller without any reservations.

Treasure Pearce

| Jun 07, 2021

HL-E - My Brother For the past month, I had been getting wrinkles on my prints and images that were ghosted. I found the solution to the As my paper was wrinkly and ripped, my fuser roller was too (matching the issues described). We spent less than we would have if we had bought You can find video tutorials online that show you how to do the repair, so You should take care to avoid breaking the bulb through the center of the roller, as it is very delicate and expensive to replace. I completed the whole repair (disassembly and reassembly) within a few hours of learning how to do it. A burning smell was present in the first few prints (that is normal).

Antonio Hodges

| Nov 22, 2020

A fuser roller was replaced on a MFC-based device I ordered 2 days ago and it arrived 2 days later. I used the online videos as a guide and it took about an hour. I have only run about 25 copies so far, but they are printing fine and there is no burning smell. My disappointment was when I found out that four pinch rollers had to be ordered from China or somewhere else in the galaxy because they were worn and were part of this assembly. That being said, had I known that ahead of time, I would have gone with another company that does include one with the fuser roller but with a much longer shipping time. I have no complaints with Yanzeo whatsoever. As of now, the product is working well. Hopefully I'll be able to update later if there are any problems.

Louisa Stanley

| Jun 22, 2021

Please make sure you have some instructions ready prior to installing this version. If you misstep on this, you might end up killing your printer in other ways.

Sevyn Rivas

| Apr 06, 2021

It is definitely worth it to replace the heat roller on the fuser unit in the hope that it will repair the fuser unit. Since the fuser unit costs ten times more, it makes sense. It is recommended however that you are a skilled hobbyist. YouTube offers a wealth of information. This is the MFC I have Now that a new roller is in place on the 9340 CDW, it is working perfectly again. It is my hope that I will not have to do that again for a long time.

Autumn Malone

| Jun 12, 2021

I used this to fix a mfc-related problem There are 9340CDW. After reading a lot of comments and guides, I found that this specific part worked well. The interior of this lamp has a painted coating that prevents overheating of its halogen lights. While I rarely review games, I definitely thought this part was great and it deserves positive.

Kelvin Sharp

| May 08, 2021