Klein Tools VDV500-123 Cable Tracer Probe-Pro Tracing Probe with Replaceable Non-Metallic, Conductive Tip and a Light for Use in Dark Spaces
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
As I said, I just tried it out to be sure. You won't be able to trace the wire in the wall, but you will be able to identify a single conductor when you touch the probe to its other end.
A live network should never be traced or toned. You send a signal (electron) to a live piece of Whether you use a $30,000 fluke tester or not, you don't connect it to live equipment and broadcast
The question is unclear. If you can connect the tone generator to the end of a Cat 5 cable, you might be able to. device is designed to make the probe touch the wire, so the signal would be faint at best. *br> *br>Not familiar with a tone generator that would work this way, but the Home Depot has a device for scanning through walls to see what lies behind them. I believe that would be a better solution for you.
When all you want to do is check for continuity, simply put an rj45 jack on each end, tone one end, and then test the other end. That way you can check whether you have continuity or not.
Selected User Reviews For Klein Tools VDV500-123 Cable Tracer Probe-Pro Tracing Probe with Replaceable Non-Metallic, Conductive Tip and a Light for Use in Dark Spaces
Toner of this quality is very nice. Build quality is good, and it doesn't feel cheap or plasticky at all. It was hard for me to tone RJ45 to Since the toner uses a RJ11 connector, it only transmits the tone down 3 wires instead of 8, so the sound is very faint. In order to resolve this issue, I stripped back a cat 5 cable, twisted the eight wires together and crimped them together. I have now been able to trace the wires and use all eight wires to send the tone. I find it to be very helpful and it saves me.
You've really saved me time. Upon purchasing this signal generator, I was hoping to diagnose a bad 120-volt electrical system The electrical system in my motorhome is 12 volts. The schematics could not be used and the manufacturer was bought by another who said they did not have any either. Electrical circuits can be severely damaged by the use of this tool. I could not use the outlets behind the TV in the front of the hotel. Behind an outlet by the TV in the bedroom, I noticed that there was a Romex cable. With the conductors and the outlets in front, I attempted a continuity test, but it failed. It is believed that the front Romez faded into the wall that was used Despite my best efforts, I am unable to energize my generator, which I have to use in order to trace house circuits. This one was very well organized and had everything it needed straight out of the box when it arrived. Through the upper cabinets and upper ceiling down through a few closets rite to the end of the Romex connector, I was able to trace the signal through the upper cabinets and upper ceiling and trace it to the disconnected end of the All of the wires were hidden in the ceiling. had been damaged in some way but the signal was still able to travel to the other end of it after it was loaded and cleared. Despite a week of searching and testing, this little tester came up with a solution to an impossible problem. The front outlet has been working after rerouting a new piece of Romex.
You never have to worry about quality with them. It is possible that I am biased because I own almost everything Klein, but I don't have to speak highly of it for it to be a quality product. I have saved myself many headaches in attics trying to locate a wire that, yes, was underneath several layers of spray foam insulation that ran the entire length of a house. The wand's accurate readings, multiple tone frequencies, and great range has made my work better. My tool kit will not be complete without this.
This probe was purchased along with the Scout Pro2 series, which is shown under "Kudos also bought". The Scout Pro2 instructions state that only the analog tone probes (VDV500 - The number 60). The newer and better 060 model probe cannot be purchased without spending more than two times as much as this newer and better model. Are there any things I am missing Using a cable tester for more than one brand is too confusing. Why is Klein not able to design probes for more than one brand of Although the light is a nice feature, I don't think the sound quality is as great as it should be.
A clear and unmistakable signal is produced as soon as the tool is connected to the earth and phase of a wire. Despite the number of wires in a 4 gang box, I was able to make this tool work. Wires can be instantly identified when they are in sight. * Please note that I did not check the tool's performance when detecting.
The home we purchased had dozens of unlabeled low voltage runs who we weren't aware of when we bought it There are two types of coaxial cable cable CAT6 and cable CAT5. Using this device, I was able to sort everything out and label everything within a few hours. It is very simple to use and can find wires that are.
I now use this probe to toning live jacks (Phone system, low voltage from phone company), where I must use my southwire toner to get a tone, and then I use my that, the light is very attractive and I really like the way I don't need to press a button to turn it on and toning.
The toner itself is fine, but the speaker on the wand is terrible. It is necessary to physically touch the wire for tone to be heard, even when the volume is nearly all the way up. If you have ever toned cable, you know how frustrating it is to try and find wire in a rack full of patch panels or in bundles of cable. Although earphones will provide a louder and clearer sound, you may still have to plug in the cable for them to work. Yet, that does not change the fact that this speaker is garbage. The speaker in my old wand had failed, so I bought this new one to replace it. We were unable to get a one because the speaker was weak.