Wixey Digital Angle Gauge Type 2 with Magnetic Base and Backlight
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Their resolution is the same, but their accuracy is not. The TYPE1 has a precision of. 1 deg. The TYPE2 has a precision of and the TYPE1 has a precision of 2 deg. Despite claims that the TYPE1 has been discontinued, it is still listed as available on the Wixey website. Anyone who claims that the only difference is the battery and backlight hasn't read the manufacturer's specifications.
The WR300 does not have this feature, but the Wixey WR365 does. The WR365 combines differential angle and level functions into one device. Dead Level Technology is used to calculate level in the WR365. The level measurement is based on earth level (much like a bubble level), but it is calibrated at the factory and stored in the gauge permanently.
Sure. It is an instrument for calculating angles. It can be zeroed out at any point and then measured from there.
For the baseboard, I'd go with a digital angle finder.
Selected User Reviews For Wixey Digital Angle Gauge Type 2 with Magnetic Base and Backlight
I used it to fine-tune my table saw, but once I started cutting, the blades were out of alignment. Everything was off when I used the old-fashioned method of measuring by hand. I realigned the old fashioned way, and my cuts were perfect; however, this tool is useless because it is 3 degrees off. When I contacted the seller, they stated that they would discuss replacing it with their managers. They left without returning. If they had been responsive, I would not have written this, and I've uploaded a video of me setting it to zero and rotating it clockwise and counterclockwise to demonstrate its inaccuracy.
) This is one of my favorite indicators. It's simple to use, appears to be very accurate, and it assists me in dialing in my blades on my table saw and mitre saw. br>br>I've never been happy with using a square because you still have to rely on your eyesight. This method entails zeroing it on the table, then sticking it (magnetized) to your blade and adjusting it to the proper angle. There's no need to guess with the saw's built-in angle indicator, which has thick, difficult-to-read marks. Great deal! br>br> EDIT: br>br> Sadly, I discovered that it is also extremely durable. I left it attached to the right side of my mitre saw blade (stupid, I know) and didn't notice it because I was looking at my cut line from the left side of the blade. When I pulled the trigger, the poor gauge flew across the garage after hitting the blade guard. On its way to slamming into my cabinets and then falling to the concrete, I'm sure it meticulously measured all of the angles it was encountering. I picked it up after saying a few curse words. On the cut bed, I zeroed it out and glued it to the blade. It's all right; I've learned my lesson. The gauge is very thick.
The information is precise and easy to understand. I have two digital gauges, as you can see in the photos. They were both double-checked using a machinist's square and a 45'. Both are fairly accurate, but the Wixey is easier to read and does not change as frequently, allowing for a faster readout. If I had to pick one, I'd go with the Wixey.
I saw a couple of negative reviews but a lot of positive ones, so I bought it. The one I got was fantastic! It repeats itself, and my machinist square says it's dead on accurate. Definitely within the range of 0. 1 deg. according to the description br>br>Mine does not have the slow response that some have complained about; At the very least, it's not too slow for me. I'd say it's about a second or so between refreshes. There were also a few mentions of an "ERROR" appearing on the display from time to time. Please keep in mind that the gauge is meant to show left or right angles. not all the way around. I noticed that if you tilt the gauge more than about five degrees forward or backward, this ERROR appears. However, I discovered that if I return to the upright position, the ERROR disappears and the reading remains accurate. To put it another way; There is no harm done; it is simply informing you that it was unable to read your message correctly. It's worth noting that the enclosed instructions suggest using a precision square to ensure the gauge isn't tilted front or back for maximum accuracy. br>br>Overall, I think this little device is extremely useful and well worth the money. I strongly recommend it, as evidenced by the five stars.
br>This is one of those things that I just had to have after seeing YouTubers use it to set blade angles and fences. br>While it most likely meets the stated Accuracy: +/- 2 degrees of freedom and repeatability: +/- 1 degree is a lot of real-world error, depending on what you're trying to achieve. br>After trying it out and seeing how far off it was compared to a setup block and machinist square, I stowed it away on the side of my toolbox, where it remained for over a year until I gave it away this past weekend. br>Because he has a jobsite saw and square is after-all, it will most likely help my buddy a lot. Everything is relative to something else.
I tried it out for the first time yesterday and decided I didn't want it after only 10 minutes. I'm not sure how this product has such a high number of positive reviews- Maybe it's just defective; I'd put it on my table saw, zero it out, gently pick it up or move it slightly, and carefully place it back in the same spot, and get a -. 1 or - The measurement is 2 degrees. Even if I zeroed it out and sat it for about 15 seconds, it would suddenly change to a -. 1 degree reading (probably 50% of the times I tried it) Nothing worked after I changed the battery and turned it on and off several times.
For checking the angle of my table saw blade, I use the Wixey WR300 Type 2 digital angle gauge with magnetic base. Now I can be very precise with my mitered cuts, ensuring that I've returned to a perfect 90-degree angle when I'm finished. My Dewalt portable table saw has decent blade angle stops, but they don't always return to exactly 90 / 45 degrees. If I have to change my blade alignment, all bets are off. This tool makes confirming that I'm in the right place simple and quick. I should have purchased this when I first purchased the saw!.
The table saw should be set to 2 degrees. It simplifies the process, and the magnet embedded in the unit (which, by the way, is quite strong) allowed me to calibrate different surfaces. It does, in fact, work extremely well. It's simple to store, and the fact that it's so small and only requires one AAA battery (rechargeables, of course) eliminates the need to purchase less commonly used batteries. br>br>I'm finding so many uses just going around measuring things and realizing how anal you can get when it's off by a half-degree. Obviously, it won't always replace a long level, and it will vary depending on the application, but with this traditional level as a laser level, I believe you're set in terms of getting things square every time; for woodworking tools, this is a must have!.
Related Products For Wixey Digital Angle Gauge Type 2 with Magnetic Base and Backlight
