hunhun 10-Pack 3.3ft/1Meter U Shape LED Aluminum Channel System with Milky Cover, End Caps and Mounting Clips, Aluminum Profile for LED Strip Light Installations, Very Easy Installation
Score By Feature
OveReview Final Score
Questions & Answers
The answer given in the first paragraph makes the most sense to me. As long as you use the LED tape directly on the channel, there will be no issues. Keeping an eye on the ends, where the wires are soldered, would be the only thing necessary. Under the end contact, place a small square of electrical tape to make sure the contacts are not damaged. We installed thousands of feet of channel and never had an issue with
A lower voltage can be applied to the led strip to reduce brightness. am not familiar with your application, but as long as the power supply delivers enough amps to drive the leds, a voltage-adjustable supply will work. About 6 amps is required for one light strip that has a length of about 16 feet. There is a possibility of up to 14 horsepower in a car I would use a dc to dc dc reducing power supply for the 5 volt requirement. With the use of a voltmeter and small screwdriver, turn the potentiometer off the power supply to set the voltage to the desired
You can use them as saw guides, but they are not the kind of thick, stiff piece of metal that makes a good rip guide. A piece of steel angle is stiffer than aluminum, and can be purchased from a local home center or hardware store. In 3' long angles, even a 1/2x1/2 1/8" thick angle should be able to provide enough rigidity. When 8' long, a 2"x2" 1/8" thick aluminum angle will make a noticeable difference in stiffness over 1-1/2" thick aluminum The dimensions of the paper are 3/4" by 1" It is about as stiff as a 1/2" square tube with a 1/16" wall, but in steel, a 3/4" x 3/4" or 1" x 1" angle is stiffer than any aluminum angle larger than the largest one all over the place.
Selected User Reviews For hunhun 10-Pack 3.3ft/1Meter U Shape LED Aluminum Channel System with Milky Cover, End Caps and Mounting Clips, Aluminum Profile for LED Strip Light Installations, Very Easy Installation
Immediately after installation the extrusions are straightened, the diffusers are fitted well with a peel-off scratch protector, and the end caps are well positioned. I find that the metal mounting clips included with the package are much more reliable than the plastic ones mentioned There are screws and plaster anchors included in the package. The kit is complete once all the pieces have been added. In conjunction with a PIR (passive IR) motion detector, I used these.
This can be considered a great price since it was almost half the price of cheaper All sellers seem to get these from the same supplier as the standard single row LED size with frosted covers. It was the hardware provided that was different. The mounting clips on the previous purchase of channels from another seller were made of plastic. The metal clips on these are tough enough to not break if you get carried away with your A hacksaw is the best tool for cutting them, as most channels are. A tubing cutter with a single blade can be used for trimming covers. You can expect more from me. People tend to install shiny granite countertops if they keep doing so.
Despite trying to snap on the Philips Hue Lightstrip cover, the Philips Hue Lightstrip was unable to fit in the aluminum channel. We were able to easily remove the protective cover by removing the clear Considering there are some areas of exposed solder there may be electrical shock risks, so it is best to turn the power off before doing this. You will want to take care when removing the clear cover so that you do not damage the flexible circuit board that The cover is not that noticeable in photographs, but it does conceal the harsh raw bare LEDs when they are off and does a great job of taking away their harshness. Under cabinets or behind pelmets, they're usually hidden from view, so this isn't always an issue. During the day, I installed this product on the underside of our cabinet, so that we can see the lights when we're sitting in our living room. In the second photo, which you can see in the one with the wood covering the bottom of the cabinet, you can see this sort of thing.
The channels I used for mounting LED lighting under my fifth wheel trailer were very helpful. attached the channel to the frame using this channel and some VHB ( very high bond) 3/4 inch wide double sided tape by 3M. Installing the lighting strips and LED tape inside the channel required using a better grade of double-sided tape on the LED strips than the China crap that came with it. LED strips that fall into the channel will burn the translucent cover that snaps into the channel if the heat from the LEDs is too high. As well as some 12 amp step down power supplies in plastic boxes under the trailer set at 11, I used some batteries for the trailer. It is best to leave the strips at 5 volts dc so as not to overdrive them. The battery can be charged by any alternator that puts out up to 14 volts dc, and the LED strips can be charged by any alternator that puts out if the trailer wiring is connected directly to the LEDs, the LEDs will overheat and the LED strips will fail sooner. In addition to all the wires and connectors and wiring, there is a split loom, which has to be connected before mounting and installing the LED channels and lenses, and you don't want to do all that again later because an adjustable power supply didn't work out. Get the job done right! These channels finish off the job and make the LEDs look as though they are factory installed through This line of kits appeals to me. I wouldn't buy the 3 if I had to do it all over again. This is a three foot long channel. In my opinion, the 6 would be a good purchase. Rather than 4 foot channels, use 6 foot channels. In addition, they can travel farther with fewer joints and are less costly. They will be cut as needed with a hand grinder, then I will clean the ends up with a small file. In order to install end caps that are water resistant, clear silicone may be used.
There are a lot of pains involved in measuring.
My installation of these just took place Some people have said that installing diffusers is a tedious task and that's completely offending to me. It seems I may have missed something, or maybe the supplier fixed the problem, but I was able to turn on my diffusers without any trouble. Then I installed the diffuser right on top of the mounting clip with one channel in place first. To tell you the truth, the first thing I did when I received the box was to check the diffuser's The price of these is very reasonable. There are 10 units in each box. There are 30 feet of water. On this day, I completed the cabinetry for the laundry room. With these, I will replace the fluorescent lighting in the kitchen. You can use under cabinet lighting as well as over cabinet lighting. After I finish my workbench, I should have some left over so I can finish my desk. Hopefully, there will be enough mounting hardware available.