Power Socket Inlet Module Plug 5A Fuse Fuse 5pcs Female 16-14 AWG Wire Spade Crimp Terminals 3 Pin IEC320 C14 10A 250V Socket Switch
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
It isn't simply a matter of connecting a few extra wiring leads. You might need a few extra pieces of equipment to fix it so it will only light up when you turn it on. An actual crimping tool (not pliers) and wire are required along with This needs to be fixed The jumper in connection with the post marked "3" needs to be disconnected and the neutral wire connected. Therefore, you need to unplug the side of 3 connected to the center (leaving the other side of 3 connected). The 3 posts should be empty when you're done. That's all there is to Whenever the button is off, the button will be off, and whenever it is lit it will be lit.
My red and blue wires have been removed from mine. However, looking at one of the product photos, the red wire is the "hot", making the blue wire the "neutral".
The VH3 size is the terminal size for the power supply. Thank you for your question. In the nineties The middle of a 2P 3P sheet is blank, welcome to place orders here, if you have any questions, please contact us at any time
Hi, my friend, thank you for your question. As you asked, the white thing you see is a female plug (3 pins, pitch Thank you. Connection 56mm), please connect the appropriate plug, if you encounter any problems, please contact us immediately!
Selected User Reviews For Power Socket Inlet Module Plug 5A Fuse Fuse 5pcs Female 16-14 AWG Wire Spade Crimp Terminals 3 Pin IEC320 C14 10A 250V Socket Switch
It is well constructed, and the overall appearance is pleasing I particularly like the socket, fuse, and switch as a single piece, which saves room in my project. Overall, I am very pleased. *As others have noted, there is a problem with this module, and that is the light will always stay on, regardless of whether the switch is on or off. Because the wiring on the switch is twisted, the switch does not work. In order to fix this, you need to swap the red/blue pair of wires with the black pair at the place where they connect to the switch so that the light only turns on when the switch is in the ON position. On my module, the black wires are on the left, while the red/blue are on the right. If you look at the back of the device with the switch at the bottom, that's how it's shipped. Putting the red/blue pair back in on the left side requires unplugging the red/blue pair from the right side and replugging the black pair on the right I am not able to post a part number, but I hope to contact you as soon as possible. Additionally, of course, you should ensure that whenever you swap the wire pairs you keep the wires from each pair in their identical positions to maintain the hot/neutral relationship.
I appreciated the fact that the first one came prewired. As a result of having an unreliable power supply for my Anet A8, I had to cut the power cable to connect to the PSU It is not a big deal though since the connector is compatible. Unfortunately, I cannot figure out how to set up the wiring setup so the PWR Button LED only turns on when the switch is Presently, the switch can be turned on or off without turning the light Overall, it works as intended, but we will update the post later if there are any issues.
It was corrected anyway, but I did not notice it at the time. My opinion is that the wires were wired incorrectly in the delivery! All the time, the red light was on. No matter what position the switch was in, it was always on. Turn on/turn off. The added feature of a light was rendered Having to reverse the Blue and Black conductors on the far left of the switch (when viewed from above) helped. In the end, this changed two things Not only does the red status light now come on ONLY when the switch is ON and supplying power, but it also disconnects the NEUTRAL and HOT wires from, respectively, the switch and the load when the switch is off. In English, the instructions (in broken English), do nothing for you. The basic message is As soon as the switch is turned on, the power is turned It is not possible to turn off the power when the switch is If you do the wiring correctly, then the product will work correctly and as expected.
The reason I gave it only two stars is that the light stays on because the wires are twisted. They are also difficult to connect The batteries don't last as long when run at higher currents, according to some people. My 30 Watt 3D printer supply should still be able to operate on the 5 amps included in the set.
It isn't simply a matter of connecting a few extra wiring leads. You might need a few extra pieces of equipment to fix it so it will only light up when you turn it on. An actual crimping tool (not pliers) and wire are required along with Here are the steps to fix it Connect the jumper associated with "3" to the neutral post and remove the jumper connected to "3". Therefore, you need to unplug the side of 3 connected to the center (leaving the other side of 3 connected). The 3 posts should be empty when you're done. That's all there is to Whenever the button is off, the button will be off, and whenever it is lit it will be lit.
This made the job look more professional for power hookup.
The product works well, and it is well built. I would rate it 5 stars if it had a template for cutting out the shapes.
You can expect it to do what it says it will. There is some question about the security of the switch, and it is quite cheap. It is critical that you check the spade terminals because one was not installed properly.