ElectroCookie Solderable Breadboard PCB Board for Electronics Projects Compatible for DIY Arduino Soldering Projects, Gold-Plated (5 Pack + 1 Mini Board, Blue)

In addition to the visible solder pads, under the black paint on the component side, the entire board surface is solid copper, and after scraping some paint off the surface (in an area of the board that is safe to do so), can act So long as no good argument is offered to contradict me, I'd say it would be wise to do so whenever possible, since explicitly connecting the plane to what you are using on the ground can save you from a lot of intrusive noise and cross-haze problems Let's talk about it, etc. My only wish would be that I had discovered this feature before completing my latest project, since it would not only have reduced circuit noise, but had also made layout much easier since so many of the parts had connections to ground, and I could have avoided the need to use so many lengths of wire. (Note when using this feature, one must still consider how traffic will flow across the ground plane, and isolate any noise-producing aircraft there might otherwise be. (I only realized I hadn't Googled this before I began this review, but it should bring up enough results)) I might be able to explain this by searching for "star ground topology" on Google.

Aviana Matthews

| Dec 05, 2020

My IoT projects have been experimenting with Arduino and ESP32 on breadboards for quite some time and I decided to take the plunge into something more solid. am a fan of these boards, except for one. It almost caused a disaster for boards like this. Maybe this is normal for boards like these. A high quality silkscreen on the front of the board makes it easy to read. In this case, the lettering is in black on the back of the black one. The only issue is that the A- is not in the middle of the A-. Reversed lettering appears on the back of the shirt. There is no change in the order of numbering. Keeping my 5VIN on the J1 when I looked at the front was necessary. J1 is really C1, so C1 from the front end is J1.

Though maybe this is how it is normally done, according to my senses it seems to be backward.

Bella Sweeney

| Sep 29, 2020

These breadboards have a few points. 1) The busses run according to usual procedures. There are (+) and (-) symbols on the sides A) on the long side of the power bus. 2) The left and right power busses are separate, but there is a wire connection point in the middle of the top and bottom of the chassis where a jumper can be attached. As you can see in the bottom of my photograph, the jumper is joining the ground. It was really nice to use as part of a recent project I was working on.

Mikaela Cruz

| Aug 13, 2020

It has a very solid/rigid feel*- A silkscreen exhibiting clear and consistent voltage lines (+/- b) clearly labelled. Please note Br>- The soldering iron is a convenient tool Introducing a bridgeable jumper gap that connects the power rails on either side. The quality of the bridge is superb
- The Golden Thru-way I am amazed that the holes are plated (as in tin/plated through the whole thing). In addition, I can attest for the quality of this board, as the hole tin will wear off after a few solders/desolders each, or if you decide to do any extensive rework on it. Not these boards, I've soldered and desoldered the pins and wires from each of them 4 times After using the system for 5+ times, we have seen no significant degradation in the throughput There is a hole plating process. That's what quality is all about. If you have already breadboarded your project and wish to implement it in semi-feasible steps, then You should buy one of these amazing protoboards the moment you see them! Whether you plan to use it for samples or simply to show off, they are excellent! I give you an A+ for I also appreciate the extra miniature protoboard, which is quite cute, although it is a small one. Besides offering larger protoboards of the same quality, they also offer a variety of larger sizes.

Boston Harrell

| Feb 22, 2021

This product is very nice in terms of build quality. It's comparable to Adafruit boards, but at a much lower price. Despite the fact that black is a very nice color, I find that it's a little harder to track things on a Obviously, this is a problem for me and I won't criticize the company for it, but if anyone else is in the same boat, perhaps they should go with a higher contrast colour. There is just too much cuteness in the little board to use it all Whenever I am cutting or stripping wires, I use it as a measuring stick.

Jad Montoya

| Jan 22, 2021

Very nice The 6-mm size). Due to the holes being plated through, when I needed to replace a soldered-on part, I had no trouble It would be a great idea to buy more if I need it. The "SK-" is not a great fan of mine We cannot use temporary white breadboards of the 10" style, as the connection is It gives me a completed board so that I don't have to worry about anything not working next time I turn the power.

Brooks Sims

| May 31, 2021

A through hole plating is applied to the double-sided component. The look great, are very sturdy, and are easy to solder! This is a company I would certainly recommend to anyone. I will definitely order more circuit boards when the need arises. No damage was done to the product as it arrived on time and well packaged. I really like this product.

Celine Hammond

| Jun 16, 2021

These will serve as the backplanes for a wireless thermometer intercept circuit that This enables me to connect the two displays, photoresistor, DHT22 sensor, and two Arduino Nanos together without extra space to spare. That's good, because I want these to be The set I have now will be used up soon and I will be buying more.

Zainab Pittman

| Jun 30, 2021