Gardner Bender GSW-41 Electrical Appliance Rocker Switch, SPST, ON-OFF, 16 A/125V AC, Spade Terminal
Score By Feature
OveReview Final Score
Questions & Answers
Yes, I do. The power supply is rated for 120 volt AC/16 amps however, it will also work on lower voltage batteries as long as it isn't overloaded. It should be safe to use light bulbs, fans, small motors, electronic circuit boards, and automotive accessories. Hopefully, the switch should be able to operate at 11 volts, as long as the internal light does not illuminate.
I was able to get it to work. These devices fit into the space of the switch because they are a standard size unlike many other items.
I have updated my response. This switch is drawn in a drawing I found online. This is the The numbers 5 and 18 correspond to each other. In the following, the measurements are (L x W). A 1- to 1-1/2 scale would be about right This is 1/4 x 3/4 inches in size. How high is it (what is its depth? ), , however, is about 31 mm from tip to collar, which is about a mm and a half There are 14 inches between the ribs. Please accept my sincere thanks for your help.
A 120V A/C switch will not light the pilot. C 14v DC will not work.
Selected User Reviews For Gardner Bender GSW-41 Electrical Appliance Rocker Switch, SPST, ON-OFF, 16 A/125V AC, Spade Terminal
It fits perfectly with my rigid shop vac which is exactly what I was looking for. Wiring is suggested on the card for illumination of the lamp when the switch is turned on. In order to have a lamp always turned on when the switch is on (e. g. The shop vac is plugged in), so To the center terminal is the line, the neutral goes to the brass lamp terminal, and the switched load is connected to the Lamp contact is wired between the two tin plated terminals, and the switch contacts are between the center terminal and the brass terminal.
You can save a lot on a small switch for this price. For my car, I used it for wiring an led spotlight. The little red dot that I thought was going to light up wasn't going to light up as I expected. You do not see an LED in the red lens. I cannot see any light coming from it. Could it be that I'm the only one thinking this?.
In my 1G Scion TC, I've used this switch (and its 3 position cousin) a few times to power charging ports and dash cams. I really like the way they fit. A Toyota highlander of the same year would be the best vehicle for them. Suitable for older Toyotas 10) are likely your best choice when adding interior switches to the new.
The switch looks good and it is nice but stupid me, I ordered the wrong one. The switch will eventually be used for something else at a later date. I didn't pay attention when I ordered this and thought that I was ordering a 4 pole switch while it was only a Taking responsibility for your mistakes is a wise decision.
On my Husqvarna lawn tractor, there was a problem with the switch that controls the headlights. I verified the issue with a tester, and then checked to make sure that the headlights were working by crossing the two cables. I was looking for a cheap, double connector rocker switch, and found this one that was labeled ordered it for my project since I couldn't see anything special about this switch that would make it just for "appliances". All of this tractor's parts were functioning as they did when it was new. It only took about 30 seconds to replace the switch.
I was able to still use the heat after my switch that controls the height of the flame got jammed after about a year of use. The switch became stuck after another year, so I had to replace it. An acquaintance of mine took a look at the set up and said they might be able to fix it if you can I found the switches on Amazon (have I mentioned how much I enjoy buying things from *enough*, my friend plugged the new switches into the wall and lo and behold, I had my heat back. Greetings from Amazon!
Thank you very much! Whenever we need you, you are there to save the day!.
It is of excellent quality. The Gardner Bender GSW is A 41 rocker switch for electrical appliances, SPST, ON-OFF * * * Spade Term, 16 A/125V AC * * * * *Bound to this exact switch for dimensions and current handling. I still think it's a great program. Brands that have a good reputation.
The picture made it look like it was manufactured in the USA, so I jumped at the chance to buy it. However, it was sourced from China, There is also an error with the dimensions they are listed as The shank is designed to fit a 7/16" x 1" opening, however, it's probably more applicable to a 3/4" x 1" opening The opening is 1/2 inch wide. There appears to be no indication of 3/4 HP 125-volt in the switch description or on the switch, although the description does mention that it is 125-volt. This power supply has 250 VAC's. Note that even though it says 'Fully lighted', that is not the case.