Accusize Industrial Tools 3/4 in. Annular Cutter Extension for a 3/4'' / 19.05 mm Weldon Shank Annular Cutter, 1" Long, Weldon Adapter, 0519-0025
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
It doesn't seem to me that such a setup would be problematic. In order to find tight tolerances, you should check the run out. A couple of adapters and some DOM tube gave me a 20 inch extension for my mag drill, but I attached it to the drill using my adapters and DOM tube. In my opinion, it was ok for my hole to be plus or minus On Friday, June 25, from 625 to 725. The alignment of 125 is off. As a starting point, I would recommend cutting at a slow speed.
MC00- would prevent this from happening A Weldon shank measuring 1 1/4" can be used with 0432. There may be a need for There are two types of shanks, 0004 and 0005.
Approximately 3/4 inch is the inside diameter. Thanks a lot.
A complete list of annular cutters that are under 2 in size Weldon Shank is 3/4" in diameter, with a 3/8" diameter bar. *br>If your drill press has a 3/4" chuck, then it is compatible with any size drill bit, from 7/16" up to 2" The Accusize annular cutters 3/8" can be used A Morse Taper 2 adaptor is required if your drill press was designed for Morse Taper 2 spindles It will fit in all sizes from 7/16" up to 2" (Morse Taper 2 to 3/4" shank) Cutters with an annular diameter of 3/8". The adaptor MC00- should be used if your drill press had a Morse Taper 3 spindle. If you use the 0003 (Morse Taper 3 to 3/4" shank), it will fit all sizes from 7/16" to 2" Cutters with an annular diameter of 3/8". The Morse Taper 4 adaptor MC00-Z must be used on your drill press if Morse Taper 4-spindle was installed. If you use Morse Taper 004 (Morse Taper 4 to 3/4" shank), it will fit all sizes from 7/16" to 2" Cutters with an annular diameter of 3/8". When a drill press is equipped with a R8 spindle, then MC08-type adapters are required If that fits 7/16" up to 2 inches, then it will fit all sizes between that and 0034 (R8 to 3/4" shank). Cutters with an annular diameter of 3/8". For instance, you could use one that had a 3/4" chuck if you have a magnetic drill. With all these cutters, you can cut annular rings. You can find an Amazon listing of the annular cutters and adapters for all of these. Accusize Tools can be found on this page. I appreciate your kind words!
Selected User Reviews For Accusize Industrial Tools 3/4 in. Annular Cutter Extension for a 3/4'' / 19.05 mm Weldon Shank Annular Cutter, 1" Long, Weldon Adapter, 0519-0025
Does the job.
It is of high quality.
To extend an angle bit, I'm using this. It works great for my mag drill now that I built a stand for it.
A liked the price and the versatility of the product.
Despite the bad set screws, the rest seemed to be in good shape. New screws from the US should be used in place of the old.
Set screws are bad, but otherwise it's an OK product.
The screws are pretty good, but the set screws aren't so good.
A liked the price and the versatility of the product.
Related Products For Accusize Industrial Tools 3/4 in. Annular Cutter Extension for a 3/4'' / 19.05 mm Weldon Shank Annular Cutter, 1" Long, Weldon Adapter, 0519-0025
