STEPPERONLINE Stepper Motor Nema 17 Bipolar 40mm 64oz.in(45Ncm) 2A 4 Lead 3D Printer Hobby CNC
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
For a 3D printer, it might be best to use the TMC2208 or TMC2209 if your printer's control board supports UART. The drivers for steppers are configured.
The amount of acceleration that can be achieved may be reduced if you ramp it up slowly while no load is applied. Ideally, the speed (RPS) should be between 60 RPM and 1 RPS. A 120 RPM (2 RPS) spinner would be possible. If you are interested in DC motors, please look at brushed or brushless versions It is possible to spin them up to 20,000 RPM.
A 5mm shaft is indeed used.
Selected User Reviews For STEPPERONLINE Stepper Motor Nema 17 Bipolar 40mm 64oz.in(45Ncm) 2A 4 Lead 3D Printer Hobby CNC
As for this motor, I beat it up by holding it still while it tried to hold, and turning it as it tried to hold, but it didn't complain. It still responds quite well despite getting it insanely hot in an attempt to get it to really work. In other words, I have nothing but good things to say about (I plan on using the same seller to order the 84oz motors for my application.
Two of these were ordered to replace my Z motors on a RepRapGuru I3 machine. Only one of the wheels was damaged, but I decided it would be best to replace them as matched pairs and keep the second spare for any future The motors could be swapped into the stock unit with a bolt-on replacement. It is true that this item has a higher amperage rating and a bit more torque, so I can overlook that You gain nothing from the trade if you just drive them a little.
It worked pretty well this weekend for me. I've been using it all weekend, and everything seems to be working well. Having recently changed back to the stock block with the all-round extruder, I haven't gotten around to reinstalling the Flexion extruder kit back on. That can definitely be powered by this thing, but metal upgrades are definitely available. I am not really concerned about noise (although nothing is really noisy when I sit next to the fans which come with the Wanhao) and I haven't had any problems with clogs or skipped steps. The stock motor is 34mm, so a 6mm difference in size in a wheel is negligible to me, and the increase in torque was worth the sacrifice. The heatsink also had to be modified since the shaft is a little longer than stock. One note, however I had to remove some metal from the heatsink to make it fit. As well, make sure to adjust your voltage with these, as the stock motors run at a significantly lower voltage.
A direct-drive MK8 Bowden extruder along with a large Kossel delta drive is what I'm using it for. The motor should be run at a speed of one The amp only slightly warms it up and provides plenty of torque to push it over 120mm/sec ABS print speeds. It has a layer height of 3mm. It would take a LOT of plastic to extrude that much. It's a very good motor and I will continue to use it for all of.
This was the first of several I purchased. There was one that didn't have any torque and I had to return it, but for the most part these work well.
I've used this stepper for a long time. It is considerably quieter than my old stepper for my old 3D My plans for using these will probably continue for many years.
My FT 2020 i3 is using Stepper for the Y axis. It works splendidly. There was a droning noise whenever the bed was moved long distances at a high speed with the stock motor. There was a big difference when this one came along. A rated motor was used in the stock engine. There are some electric weights that weigh 8kg/cm, but this one seems to have adequate power for.
It's a very good stepper motor for the ROBO 3D. I built a clone, and it works perfectly with the RAMPS and the Although I would have preferred a motor connector, I can always add one myself. The wires are long enough, and the connector would have been nice on the motor itself. Amount of drift or double-counting issues is not present There are steps. All 5 motors of my machine would be strong enough to run on it.