ERYONE ABS-Like 3D Printer Rapid Resin 395-405nm UV Curing Photopolymer for DLP/LCD Printer, 500g, White

In addition to submitting a review with pictures, I submitted one over a week ago, but Amazon must have lost it before accepting Due to this, this will not contain the same level of detail as an article. In case you were interested, this resin was tested with a Phrozen Sonic Mini 4k printer (mono screen). It is important to note that this resin is very strong and that it does not smell bad at all, like most other Eryone products. With its wide mouth bottle, it is easy to pour (and clean out vats). Although the print may seem a bit flexible after the print is finished, when it's cured, it'll be a very stiff material I am a hard worker. Break a part (or a To that end, I calibrated this resin with various calibration prints, which took me many hours. Even so, the resin exhibited very poor performance when calibrated to those settings. The pictures above depict the situation. Also, I have found that Eryone's standard resin is capable of the same. It should be noted that only professionally prepared materials are printed Models supported by Loot studios or 3D printing pro were too complicated for me to use, and even then I had to add dozens of models Supports need to be up to 60 percent heavier (and more comprehensive) to allow models to print properly. There would be one model that would work and others that It is also important to note that I had no problems adhering the plates. There was no failure of plate adhesion for any of the prints. Typically, failures occur in thick boundary areas that should not need support in the first place, and this is where the body of the model often fails. To summarize, once I increased exposure to 3, I noticed that my skin had become much more vibrant. The speed is 7 seconds per second. If I hid the layer at 05mm height, I got a better result (although still not reliable). Approximately 15-percent more exposure was achieved on that layer Exposure times are over calibrated by 20 percent. I believe this should get a 3 for the cause. I give this review five stars. The resin could be a good choice only if it is overexposed. Furthermore, I think it's clear reading reviews here and on the Eryone Facebook page that those with color LCD screens (not mono screens) feel ABS has been much more successful in their app as reported by their customers. By Eryone, resin is a resin-like substance. It seems to be a trend under the radar anecdotally, but I have no idea what the cause may be.

Derrick O’BRIEN

| May 23, 2021

Resins like this are easy to process and offer no problems for me. As with the Ryu I've printed in my Photon Mono X, I usually print them at 45 degrees but this one I printed at 90 degrees and it worked just as well. I printed this one hollow to save me some resin and I got two copies with the 500ml resin They have a height of about 5 inches Another reason I like this one is the The material has a lower brittleness than most materials - Unlike regular resin, Ryu's headband did not break because the end was still intact even after I removed the supports, no need for superglues. If you are getting the transparent resin, make sure you treat it like transparent resin and watch YouTube videos on how to do so. If you'd like them to be more transparent, you should wash them with water. As for me, I washed mine with isopropyl alcohol and cured them with my DIY curing lightbox, which resulted in a translucent end product. Please view the attachments for photos. There is no doubt that the Eryone Abs- will be worth it The transparent blue color is really cool and is easy to print in. The material holds up well and is easy to print.

Aubriella Smith

| Jun 10, 2021

The product is both strong and prone to turning brown when exposed to UV light for more than 20 minutes. As a result of its molecular strength, I also believe you should set the attachment points for your support For the printed layer to be attached to the supports, add 50 mm. In my opinion, the larger attach size leads to an end product that appears bumpy and has the appearance of an orange's skin. The material isn't a bad choice for a print resin, but I wouldn't choose it as my first choice for a standard resin and I would only use it when certain properties are needed.

Haylee Jackson

| Jun 29, 2021

It was an excellent value for the money. Aside from the reasonable price of this resin, the odor was not overwhelming, and the large opening of the bottle made it a pleasant purchase. As a result, I'm very pleased with the way the resin holds detail on prints. The term 'ABS-' is not clear to me I really like it and it is tough I used this resin because it was not as strong as some other resin I used, but it is not I would say overall it is a good resin choice (printed on the Elegoo Mars Pro 2).

Melani Glover

| Nov 26, 2020

6" tall and printed on a Photon Mono with 2 colors, the dragon measures about 4" long. I lightened the photo so the detail can be seen since it is a deep matte black color a 6 sec exposure makes it look like a matt black. first head I printed and tried to catch it with my hands but it accelerated much quicker than I could catch it. The mustache broke away cleanly but I didn't suffer any other damage as I had dropped very small minis using other resins that sustained much more damage. This resin lasted a long time without a single failure and I will definitely buy more.

Jaycee Merritt

| Oct 03, 2020

It follows that It failed to print on my first try. Printing it with my usual resin preferences (other resins) worked fine. Despite my best efforts, half of the plates didn't work. Changing the parameters and running some calibration tests allowed me to modify those online. This was the second print and it worked perfectly. The color is clear and the detail is great. I am pleased.

Zaniyah Allen

| Jan 23, 2021

I have tried many bands and different types of resins, and this one is hands down one of the best. You can feel the power of it even when you touch it. I have a lcd mars printer that prints exceptionally well and in great detail. The resin that you suggested is definitely gonna be at the top of my list of resins to buy.

Alessia Kim

| Sep 25, 2020

The resin is excellent, very low odor, washes well from a paintbrush, and since there was no cure box, it had to be cured by sunlight and worked well. The print looked good right from the first test, and I would use it in the future.

Milo Wood

| Jun 21, 2021