Bulkhead Compression Fitting 1.5” Tri Clamp Weldless Bulkehad 304 Stainless Steel Homebrew Kettle Bulkhead

Bulkhead Compression Fitting 1.5” Tri Clamp Weldless Bulkehad 304 Stainless Steel Homebrew Kettle Bulkhead

$ 19.99

Score By Feature

Based on 138 ratings

Easy to clean

9.48

Easy to use

9.69

Accuracy

8.51

OveReview Final Score

How Our Score Is Calculated

Product Description

one to the end of the sentence. Any vessel can be fitted with a 5" TC flange! It is incredibly easy to install. You simply drill a 41 MM hole and tighten the locknut with 1pc extra food

Gaskets composed of silicone are compatible with the high heat found in the 304 stainless construction.

A wrench cannot be used on the front of the flange because it is not flat. If you tie any other TC parts on with the gasket and clamp, you will find it easiest to hold the flange in place before tightening it. You can insert a rod or screw driver into the hole once the wingnut is tight.

As small as a kettle with a diameter of 12 inches.

The weldless design is ideal for pressurized transfers from Brew Buckets and FTSs

Questions & Answers

Is there a limit to the thickness of a surface this can ?

A kettle is capable of holding up to 3/16" or 1/4" if it's flat, so if an arc is around a kettle, the length is lost

Could I use the 42mm carbide bit I already own for the ?

The hole saw I used had a 1 5/8 inch hole and I found it to work. You should take your time to do it and not rush

Just to double check what happens if both gaskets go on the outside? Tested it out and there was no leak, just wanted to make sure. ?

The outside one is on the inside and the inside one is

Selected User Reviews For Bulkhead Compression Fitting 1.5” Tri Clamp Weldless Bulkehad 304 Stainless Steel Homebrew Kettle Bulkhead

I think it would be appropriate Wire diameter of 5", My intention was to use triple-layer sanitary paper In my recent conversion of all my homebrewing gear from gas to electricity, I used clamp connections where possible

5/5

The gaskets are well made, and they have the right thickness and density to properly seal and avoid leaks when placed on the curved side of a brew kettle. To give you an idea of the size, the brew pots I use are 16 gallons, 16 inches in diameter. Through the port of my HLT, I am able to fit a 3500w Dernord heating element! I just ordered another.

Elias Whitehead

| Feb 25, 2021

It's happy and sad at the same time

4/5

In addition to liking the stainless steel, I am not happy with how poorly described the measurements are for this item.

Aylin Pruitt

| Apr 06, 2021

A risky situation

4/5

In order to prevent the o ring from sliding off, the nut should have deeper grooves and be hand tightened even if the grooves are large.

Addilyn Carr

| Dec 03, 2020

This bulkhead would be perfect if you wanted to add 1 to it

5/5

The sanitary fittings are 5" in diameter. My brew kettle accepted the app without any problems. A 42mm hole was drilled, a 90 degree bend was clamped on the outside and a crescent wrench was used to tighten it. As of now, no leak has occurred. Weldless fittings seem to benefit the most from captured O rings. The product is excellent. I would buy it.

Hallie Blake

| Apr 10, 2021

I needed just what you said! The welder does not need to be employed! It appears to be very well made Installs in a few minutes

5/5

I enjoy having it be a part of my electric brew system!.

Gloria Montoya

| Oct 09, 2020

It's a disappointing experience all the way The product was not as pictured and I still have not received the money after almost two weeks of returning it to a locker at an Amazon facility

3/5