CLONE-A-WILLY - Silicone Penis Casting Kit for DIY Dildo (Deep Skin Tone)

There were a lot of people at the event. In the case of average or above average size, I recommend purchasing extra silicone. A piece of silicone that came with it was not sufficient for my leg, I lost about 1 1/2" on it.

Meredith GODFREY

| Jan 23, 2021

Here is the information you need. We're doing okay, a little messy, but we're managing. problem is, for larger members such as 7" or more there is a shortage of silicone mix so there are a few inches lost. Even though I'm not a big guy, but I'm around 8" and so I lost about an inch. A smaller tube would also have been helpful. It says not to touch your Penis to the sides of the tube, but if you have a curve in your Penis, you are better off staying away from the sides. Especially if you're decently endowed, the best thing to do is to find your own material to cast the mold in rather than the tube, something with a bigger circumference and then buy extra mold and silicone so you can reduce it to what you need or desire. If you have not already done that, I recommend running your sink water once you have got your temperature set and leaving the water running until you have a good temperature. Finally, check the temperature once again in order to get the Added bonus you will fare a lot better if you are able to put your member down rather than standing when putting him in the mix. I wish you the best of.

Esmeralda GRIFFITHS

| Apr 14, 2021

Definitely buy a wire whisk to mix it up. Firstly, mix it very, very fast (20 seconds). When you have completed mixing, pour it as quickly as possible into It will take less then one minute to put it in because after two minutes it will already have I found it most challenging to stay hard while it was forming so it was slightly bent since I lost a little erection during that process. Since I used 2 silicone kits worth of product, it literally took me both of the kits to get it to size, so you might want to go buy extra silicone. Nevertheless, I can tell you that all of the details are absolutely perfect including the veins and tip. Therefore, I highly recommend that you buy two of these or extra silicone and molding, and you remember to mix and insert them very quickly My girlfriend kept me up all night as I knew we would have to rush to finish, so she kept me awake. When you follow my instructions, you will be happy and will have a replica of yourself that you are proud of!.

Nova Buckley

| May 17, 2021

All the failed attempts are making me laugh so hard. I love how simple this is! I would suggest that first you Look at Willy's website (empire labs) and click on all of the links there. It is just a matter of learning. The following tips and advice may be of use to you - It is recommended that you purchase bottled water if you have a well or spring at home. Put 2 pots and 2 dices into the pot Water in 3 bottles. You only need to boil one bottle of water on the stove, then remove it from the heat and let it cool. Take a second pot, fill it with half the water temperature, add half of the bottle of water, stir, and then slowly turn up the temperature of the water until it reaches 90* with room temperature and extra hot Then measure out the correct water amount and begin to mold when it has reached 90 degrees. Please note
Hire a person to help you ***
There is no point in watching the video. In the scene showing the molding powder being mixed, it appears that someone is mixing it slowly. You will need to be moving your arm really quickly to mix this, similar to beating eggs. Mixing bowl Pour 90° water into mixing bowl, start a stopwatch when you pour powder into it, and mix it as if it was an egg. The clumps in ours did not appear at all at 32 seconds, so getting it done in 45 is definitely possible. We have to expect it to be runnier than Elmer's glue and to look exactly Please note
We used coconut oil instead of petroleum because we had none. I love it!! It works perfectly! Getting the hair trimmed low will work perfectly with no pulled hairs. There is no need to shave completely. Please note
As stated in the instructions, hold into the mold until the two minute mark, but you can hold into the mold longer. Using a pry bar, we carefully loosened the top with my husband after he was unable to get it out. It is a flexible mold that flexes as you slowly release the suction. For best results, release it slowly to avoid damaging the mold. Please note
Here's a great way to use your Amazon box! You'll need to flatten the piece so that you can use it If any spills are made, they fall onto the cardboard!
- You need to size your tube first before doing this. Mark the tube with hard ink and determine if you need to follow the clone procedure Here's Willy's video on how to modify a curved tube! I love how simple it is! Duck is all you need Please note
It is possible for your helper to make clones if you are super prepared If you are doing a clone, you will be pushy The mold mix is extra for Willy. If you want to do any mixing, trim up or shave coconut oil before you start, then cut a medium sour cream container into about 1/2-inch chunks Three-quarters of an inch Put the mixing bowl under your man once you've poured the mix into the tube so that any excess mix does not spill over. As you assist him in getting a good position, making sure he is not touching the sides of the tube, scrape any excess from the bowl and quickly dump into your small It's up to you! I slapped you since you were holding me! I was holding my by half a second when we were quick like we were I got it working after one minute!.

Chaim Horne

| Oct 17, 2020

The package came fast and the product was exactly as described

if you don't have help when making the mold you are liable to mess it up and waste $40, In order to fix a "fully erect" penis you need to make sure it does not touch any sides or the top portion does not form a flat base. Otherwise you will not be able to fix it. There will be a lot of casting dust everywhere and it will make a mess everywhere it touches. You must not let the mold stand for more than 4 hours otherwise it will shrink and crack. Please note *br*br*- We all know that YOU place where you can see a video on this product - an example is here - The situation is more likely to be a failure if you do not have help or unless you have watched this video several times. Please note
There is silica (sand) in the casting material, which will cause your member to feel sandpapery when cleaned. Be gentle when you clean your member--this was the quickest way for me to waste My money would have felt more gratifying if it was thrown in a crowded stripclub.

Kristian Hansen

| Jul 08, 2021

You'll never miss an opportunity to win your trophy if you keep it nearby. It is important that you have him as a I love how this turned out! You are one of the lucky girls if you are one of us. If you can clone one, do it! In a nutshell, it was easy. This was not what I expected, and it took some time to get it set up. What I am going to say is this. Take advantage of everything that is at your disposal. He is included as well! Take a look at the directions. In addition, I recommend that a ring be placed Yes, I do! This is a crack The suggestion was actually very helpful, so I am glad I went ahead with it. I like it! It's not like today's " toys", there is a bit of a learning curve. You may have to put your trophy above your head to reach it, but it's worth it! As cheap as I could find, this is the best price I could If you choose not to add vibrates (they come with the kit), you can. As I said, yes. The reason why it's a little harder is that it's more difficult than.

Damian LAW

| Sep 17, 2020