Summitlink V3 Case Dual Fans for Stratux ADS-B Kit Fits AHRS Module and GPYes (Tint)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The board can be mounted without screws by simply placing it on the mounting posts and closing the top cover, which will secure the board in place with clips.
The second fan connects to one of the USB ports that are still available.
Selected User Reviews For Summitlink V3 Case Dual Fans for Stratux ADS-B Kit Fits AHRS Module and GPYes (Tint)
It's a nice case, and it appears to be ideal for ADS-B. B, however, it has two flaws:br>br>The risers on which the Pi board sits aren't even made of plastic, so the board is a little wobbly when it's just sitting there. To install the board, I had to shave it down with a knife; the board's power adapter and HDMI don't quite line up, but I can plug them in now that the plastic has been removed. br>br>However, the most serious problem is the small fury fans. I was planning on mounting it to the hall window, but they're too loud. Even when mounted to the window, they spin so fast that they rattle the glass, so I have to lean against the window to keep it from shaking. br>br>Unfortunately, I'll have to spend some extra cash to replace the fans with quieter models.
This is my preferred method of constructing a Stratux. I've made a few of these for myself and friends. This one has plenty of mounting options and fits all of the modules as well as two fans. br>br>However, you should be aware that this isn't the norm. Certain accessories (such as the Stratux store's suction cup mount) and ADS-compatible cameras will not fit. B antennas with a cable length of less than 5" (such as those sold at the Stratux store). The 978 antenna will not fit in any way. ) You'll need the SummitLink USB radios as well as some different antennas; I recommend the NooElec antennas with 6" cables (there will be some extra cable to tuck into the case). br>br>As some of the other reviewers have noted, this isn't the most durable or thickest piece of plastic available. None of mine have broken, but I didn't use much force when constructing them. While taking it apart and putting it back together, be careful not to break any tabs or other components. Last but not least, don't forget to put the strap in place! I always forget to attach the strap to the inside of the case when I make these, and then I have to open the whole thing up again just to get the strap in. The strap comes in handy when you need to keep your battery connected to your Stratux. The little rubber feet can be used to keep the battery away from the case itself, preventing the battery from overheating.
I really like the material used to make this case! br>I ended up screwing antennas above the raspberry pi board and placing a reyax ry836ai module (GPS AHRS) below the board (just because ipads without cellular modules don't have a proper built-in GPS and you lose your positioning at above 1000 feet)br>I only had to use pliers to remove cable holders and slightly bend the suction cup mounts, and that's when I fell in love with the material. Instead of cracking, it becomes brittle. it bends! br>br>While fans are loud, they are difficult to hear from inside a cockpit. The risers, on the other hand - I had the same problem as a few of the other reviewers. They hadn't even been removed from the packaging. I heated a knife and shaved the very tip off one of them, and now my board fits perfectly and the case closes without gaps. br>br>This is the only stratux case I've tried, and I don't think there's any reason to try another.
It appears to have been well-planned. Fitment compatibility with all current features for a Stratux setup, including a new thin usb for the second fan so you can still run an internal GPS with no fitment issues; the only problem I had with this case was that the top part of the case broke its clips that hold the bottom half in place immediately after receiving it and opening the rear most compartment to install the raspberry pi. Another issue is that it is missing the four screws required to secure the board to the case. I wish they would redesign the case to use screws instead of clips to hold it together. The USB slots are accessible through a sliding door, which I find very convenient.
After having to replace the GPS/AHRS chip, I decided that a fan controller and a dedicated case would be useful. The electronics are kept cool by two fans. They appear to be effective. The six smaller suction cups are powerful enough to hold the stratux and a large battery to the plane's window. The strap that connects the battery to the case is extremely strong (just make sure you pull it tight enough). There are even small rubbery feet that separate the battery from the case, allowing air to flow freely. It was simple enough to enlarge the holes to allow the antenna feeds to pass through.
The Rasberry Pi fits in like a glove. Antenna cable guides have been thoughtfully designed. The USB fan connector, as well as the internal GPYes, fits perfectly. In contrast to other reviews that claim the Summitlink does not fit the Stratux UAT, the V3 Summitlink version does.
The suction cups worked well for the first couple of times, but then they stopped holding the receiver vertically in place. br>In addition, the standard tripod/gopro mount part broke very quickly - It had to be replaced with a new one.
I had everything I needed to store the Stratux's components. Everything is in its proper place and functions properly. In a future version of the case, a recess for the antennas would be a nice addition.
Related Products For Summitlink V3 Case Dual Fans for Stratux ADS-B Kit Fits AHRS Module and GPYes (Tint)
