VSGO VS-S03E New Full Frame Camera Cleaning Kit 12pcs Sensor Cleaning Swab + 10ml Cleaner for Sony Nikon Canon FF CCD CMOS Clean
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
There is something attached to the plastic that needs to be removed. When you've finished with it, put it back in its place
I have a 35mm camera
Selected User Reviews For VSGO VS-S03E New Full Frame Camera Cleaning Kit 12pcs Sensor Cleaning Swab + 10ml Cleaner for Sony Nikon Canon FF CCD CMOS Clean
Cleaning the sensor used to involve the use of a blower, sensor brush, and SensorKlear. Although dry dust can be dissolved with these methods, they may not be suitable for stubborn spots, for which the wet method is the most suitable.
Taking advantage of the VSGO swab and cleaning fluid which is easy, safe, and relatively effective. It would be beneficial to design the cleaning fluid bottle more clearly, as it can be difficult to see/control the drops in the bottle. The swab will produce streaks on the sensor if it is too wet. Initially, I had a stubborn spot on my camera sensor (more of a short streak) and a regular two passes (with a bit of pressure because the sensor isn't stabilized or suspended) failed to A new swab is not needed. I reuse the current one, make two passes and find a spot (could it be oil from the shutter as it's near the top edge of the swab? In the end, I used a bit more cleaning fluid and concentrated just on that area, let the swab dry for a bit, then did the usual sweeping from left to right, then right to left. This is probably the same swab I used in step 5 I had to clean the sensor six times before it was spotless. As a general rule, if you are cleaning one sensor and the first two passes do not produce good results, then applying the same swab again should be safe and effective. After I sweep the sensor again, I would use a blower to remove any potential contamination on the tip. I would not only be left with a half box of swabs after just one sensor cleaning, but also with half the box. You may find that too many streaks appear on the sensor due to too much cleaning fluid on the swab. To remedy, wipe the swab dry for half a minute before attempting two more passes. Repeat the previous step (possibly more than once) if you see less streaks, and you should have a sensor that has no streaks whatsoever. If using a new dry swab, be sure to avoid streaks as the dry one may not completely remove them.
It did the job perfectly, I was having trouble with finger prints on the sensor or something similar. My sensor is now clean. Here's what it looked like after I used this swab on it. A few minutes later, it was gone. I was a bit nervous, but I watched a few videos before I conducted the cleaning. I was aware of some steps that should be taken into You must keep the Camera on and select sensor cleaning, as well as disable IBIS if it is.
to clean the sensors with the integrated feature and with the dust blower, but neither worked. In addition to dust removal, this product also helps you remove stains without leaving any trace of it There were 12 swabs in a vacuum bag The bag is sealed and lint-free The free will. No trace is left behind by cleaning solutions. As well as cleaning the front of my lenses, I used it to clean the backside as well, though the fit isn't perfect. I would buy it again, no problems.
A moistened swab was able to remove 95% of the junk from my sensor in two quick wipes. Interestingly, I had to use a second swab to remove a substance that was adhering to the sensor besides dust. I found my sensor to be cleaner after the second swab than when I first bought it from the factory. For those of you concerned about cleaning your sensor, it is nothing to be afraid of. The lens cleaner is much harder to use on my sensor than the lens cleaner on my lens.
I've cleaned sensors for 5 years now and nothing has disappointed. The first time I tested it, it worked perfectly, sensor was clean, no dust. But when I checked my a7sIII sensor the next day, I noticed these streaks or residues. Upon returning the next day, I tried to clean them with a dry swab and waited for it to dry out. Once again, you can see these streaks of residue! What a pain! I also ordered the one for the APSC sensor, but the swab scratched the TF out of my A6400 sensor. There are dangers.
Four years have passed since this camera was bought. Having cleaned the sensor this way for the first time is a new experience. Swabs like these do a great job. On my images, there were a lot of visible marks. It was so great to see the sensor so clean after several tries. The impression I have is impressive.
VSGO VS- I am very satisfied with it The S03E camera cleaning kit is a complete kit to clean the sensor and the housing. I used it as advertised, and it worked perfectly!.
When I used the new equipment for the very first time, it was easy and productive, and I was impressed with the cleanliness of the chamber.