KnuKonceptz Kolossus Flex Kable 4 Gauge Power Wire Black OFC (Sold in 5 Foot increments)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The solid copper wire I bought last week was very nice. It was flexible and nice. I am pleased with my This was a far superior product than what was offered by the stereo store.
In addition to the red and black 4 gauge OFC, I also used the Red and Black 4 gauge Neither of them was shorter than 10 feet.
Theoretically, I would say The pull of the winch ultimately depends on how much wire there is to the winch and how much power the winch has. You might need to bump up to 2 gauge, the link was for 4 gauge, but double check the amp rating and the length of the wire run. It is helpful to look at the chart halfway down and the amp ratings should be listed on the box or website such as this one You must learn. I love SparkFun. Visit http//www.com/tutorials/working-in In conjunction with I used my pencil torch to burn through solder around the eyelet opening on the Knukonceptz cable, and it worked amazingly well. Once the solder began to fill the void around, I took the pencil torch away and let it cool for about 5 minutes before moving on. I like the cable, but I think the wire is actually larger than what was shown. It was necessary to lightly trim my 0 gauge in order to fit into the 0 gauge terminals, and my four gauge had to be trimmed very lightly in order to fit into the Changing to it is a relatively inexpensive change and it's high quality wiring. As soon as it has been soldered and shrunk Wrapped in its own jacket, the jacket is extremely thick and should be able to survive the abuse that a vehicle can give.
Selected User Reviews For KnuKonceptz Kolossus Flex Kable 4 Gauge Power Wire Black OFC (Sold in 5 Foot increments)
Copper wires like these are very nice. The route is very flexible and There is a slight layer of opaqueness to the coating. It was very easy to solder ring terminals with a torch. The following is the soldering note A small plumbing torch like one you can get at wall mart or lowe's works well for heating copper ring terminals with wire inside. Solder a lot of stuff fast and heat You would forfeit your scholarship if you didn't finish within 10 days For 15 seconds, follow with a cooling down process with air or damp paper towels. When the wire gets too hot, the solder will flow up the wire, causing the shielding to melt in places you'd rather not have It can be reheated quickly and solder can be applied to ring terminal cups once it's cool. It is best to keep the heat off it for less than 10 minutes The wire shielding should only be melted after 15 seconds with just enough heat. Too much heat will melt the solder.
I've been wearing it around my neck like a necklace because it is so comfortable. The truth is out there. Getting it cut to length is going to be a pain, but I will feel better knowing my power supply is not likely to be slowed by crappy wire with a lot The weight and the way it conforms to any shape make you feel the difference when you lift the wire. Observing the cross section of the end, you can clearly see that there are multiple bundles that are intertwined through the covering. The sound system in any car would be enhanced with this wonderful addition. It's just not enough for me to say good things about these guys. Please show stinger and other crappy rip-off artists how it's Knu did a great job! As a result, I never write five-star reviews because I always find something to improve. It was a job well done by these guys.
If you are looking for power wire, this is the one I would recommend. It is a bit pricey, but it is worth it it is true to spec, meaning it is supplying what it is meant to. Despite how some cheap brands appear to be bigger, their bulk is actually made up of thicker insulation as opposed to the more important copper wire. Because this wire is so flexible, the installation process is Furthermore, it is made of 100% OFC wire. Copper of this type is preferable when installing systems with RMS ratings exceeding 1,000 watts. In the case where you have a system with less than 1,000 watts, the KCA wire is cheaper and more suitable.
Excellent product - highly recommended This product is extremely flexible and of high quality I HIGHLY RECOMMEND this product because of the thick copper wires, not the thick sheathing/ insulation as some similar products do.
My car had a 0 score when I bought it a year ago A cable without a fuse made of aluminum gauge. It is needless to say that I replaced the terminals and then they turned black within 6 months as a result. As the wire in the Kolossus was about the same size as the wire in the Kobalt, it was just You can use an internal server if you install one With a line fuse to ensure safety, this wire will pump out a ton of power uninterrupted to the.
This power cable is almost as big as a 0 gauge cable. Not the rubber, I mean the actual wire. I appreciate her flexibility and her ease of working with me. For wiring up my amp and for an upgrade of my big 3, I used this.
Knukonceptz is the best cable I have used in the past year, from speaker wire to power wire, from car audio to anything else. I've been involved with car audio for over 15 years now and only discovered it within the past year. Copper does not need to be coated with aluminum as this stuff is 100% copper. Nonetheless, they also produce aluminum stuff, and they state clearly that it is aluminum (as opposed to companies deceitfully not stating that information). It's easy to work with, true to gauge, not too expensive, and not too expensive compared to some other well-known brands Companies known for their quality. Since I started using it, I haven't looked back.
A nice, heavy, well-constructed item made with actual copper, rather than aluminum coated in copper. A power cable extension is needed for amp power cables, winch power cables, and jumper cables. I found the system to work.
Related Products For KnuKonceptz Kolossus Flex Kable 4 Gauge Power Wire Black OFC (Sold in 5 Foot increments)
