Anmbest 2PCS DB9 Solderless RS232 D-SUB Serial to 9-pin Port Terminal Male Adapter Connector Breakout Board with Case Long Bolts Tail Pipe (2PCS Female)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
It should be fine to use #18 for this, but I wouldn't go any larger than that. It looks like you can barely fit a #14 wire through it. A recommendation for wire size was not found in the documentation.
As it is made from plastic,
What I gather about this question is that you are using just two wires with a custom application. There is no difference in the origin of either wire, and you have no need to know which pins to use in this device. Because of this, you only need to know which pins to use in this device. *br> *br>For instance, if a wire has to go from point A on your control to point C on the application device, choose any pin for the wire coming from A and attach the wire going to C to the same pin on the plug on the other side. A relay circuit is not present on this adapter. It has no controls. The device consists of a wire (pin number 1 to pin number 2) being routed from pin 1 to pin 2 etc. The pros of the device are that it is easy to attach wires (no soldering) and that you can tell which pin
The cable can be plugged in as long as you know how it's wired
Selected User Reviews For Anmbest 2PCS DB9 Solderless RS232 D-SUB Serial to 9-pin Port Terminal Male Adapter Connector Breakout Board with Case Long Bolts Tail Pipe (2PCS Female)
Connectors like these are simple to wire. You can replace existing connectors with them, or, as I did, make a breakout cable from them. It's a bit confusing to look at the product photos. Is there a choice between nuts and screws on the connectors? There is a yes/no answer to In addition to the threaded insert, the connector body has a bolted screw. Standoffs may be attached to this insert or the thumb screws that are included It grants the screws freedom of movement, but does not allow them When the connector is connected to a piece of equipment, there may be some looseness due to the fact that there will be two nuts to screw through during assembly-one on the connector body and one on the connected item. Unfortunately, the standoffs shown in the product photos are not included so you cannot screw into the connectors without providing your own set of standoffs.
The connector is also quite pricey and comes with a lot of shortcomings. As mentioned above, the screws provided for mounting the metal connector do not fit, so you cannot clamp the metal backshells onto Also, it is too bulky and heavy with its metal shell. Such a large amount of metal is totally unnecessary. Furthermore, the grommets for holding the cable are either plastic or rubber rather than metal. If you do not have the correct cable diameter, even with the four sets of cable clamps, it will not grip the cable and provide strain relief. You might be able to find the right answer among four options.
Last but not least, the threaded rod is too long and can easily short on a wire if you do not strip it This seems to be an issue with the.
I would definitely recommend it. I had to give this a 5 out of 5. My joystick ended up being repaired after I used it to dry out a crack. Installs in a matter of seconds. Having a great time using it. The more I need, the more I will order.
These were used to wire a cable that I used to program my scanner. However, I am not sure what the configuration should be. It is much easier to use in comparison with having to solder and unsolder connections every time. Everything was in good shape and arrived on time. It wouldn't be the last time I order these connectors.
My favorite part of the cable relief is the rubber bushings that come in different sizes. The software is easy There are no sealant issues here. These are not sealed at all, but are.
Using this type of connector, it is easy to wire up the system and to later change the configuration. My application is well suited to them. As a result of the screw terminals, they are a little larger, so if you need to connect them to small spaces, you may need to be mindful of that, but they are easy to use and eliminate the need to solder or desolder any wires. If you make a mistake with the wiring, solder it.
A very good solution was found here.