Hitachi MAF0012 Mass Air Flow Sensor
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
My belief is that the part in question should fit. I put 2006 F150 v6 4 in the auto garage on amazon and it worked. It says yes to 2 and it is correct. In my case, I used it on the My gas mileage increased by two miles per gallon after I used the 6V8. As for the clip that holds it in the intake tube, it will break or snap. Well, I used some pull ties to fix it. I was told that if you put a small amount of caulking on the side of the connector before you slide it together that will also help keep it connected. It's ( a small amount ) on the plug connector not (the sensor )
My Ford Explorer 2004 had a hitchi mass air flow sensor that was an exact match, and it worked fine
It is a good thing to scratch out #. Therefore, it is the same manufacturer as the original equipment To sell it at a lower price, they take out the OEM number.
You're going to love it
Selected User Reviews For Hitachi MAF0012 Mass Air Flow Sensor
The SEL 2 version of the Ford Fusion is a 2010 model. Five liters four liters I started experiencing gear shift slippage at 99,800 miles after my car started wearing down cylinders. To make a long story short, they said the MAF was dirty, so Good to know the issue has been resolved. A little over 103,000 miles into the trip, the problem reared its ugly head again. The MAF was cleaned with some MAF cleaner spray, then put A total of 104,500 miles was covered during the flight. Quite simply, the MAF used for the original study was substandard. Checked the air filter to make sure it was clean and replaced it as well for good measure. As I read reviews and saw that the numbers on the packaging were scraped off, I was a little suspicious. A MAF was available at local auto parts stores for $125-$150 A 200-dollar donation. You could get this delivered same day through Amazon. ordered it around 7 a. m. , and it arrived around 8 a. m. It is usually delivered to my house by 8pm (typical delivery time). On the very next morning, I installed it, and the car has run flawlessly ever since. Here are some suggestions and tips for the DIYer. 1. You must check the direction of the arrow at the bottom of the old MAF prior to removing it. I had to hunt for and retrieve the dropped screw for about 15 minutes. * Without the lost screw, the total installation time would be This will take about two -A minimum level of skill is Do you know if a toaster will work? Would you be able to unscrew two screws and reinstall them? A Ford Service quote for $427 is available. Cost to do the complete project $66. 62 (Parts plus labor)
Total cost to DIY $93. 89 $53 plus tax.
In retrospect, it never got in great gas mileage. However, it got an awful lot worse in the end, so I used fuel line cleaner all the time. Then I changed my oil, using synthetic oil with the Getting a bad gas mileage is back to the way it used to be. Seeing as I got 4 more mpg so far, if your car or truck is running rough, try this change and It Worked For Me and I'm Sure it will Work For.
When I started it up and drove it, it worked well. It has so far been a good experience with this, since I installed it in my Ford Expedition today. I was able to restart my car and it runs well In the past, I have purchased 2 other batteries and when I installed them on my truck, I couldn't even start it. The manufacturer has provided nice new packaging and boxes for the product. Upon removing it, I found that mine are old and worn out, so I would like to get replacement screws.
It is odd that the box says "Made in Japan" whereas the item itself, with its serial numbers removed, says "Made in USA", which is obviously suspect. It is not entirely clear to me whether the part is of good quality or if it is reliable, nor would I want to risk finding out, since I do not want anything to do with a company that makes this kind of misleading, false claims.
In this case, the price is less than the one at the auto parts store, but if it is remanufactured or a secondhand one, the price should reflect that.
We bought a used Ford expedition in 2010 and found out the car had rough idle after the car warmed All spark plugs replaced and it still did not work. I know why there is no code, but there is none. It worked! Car started up and stopped for no apparent reason. I hope that is the source of the problem. ***Update*** the air flow sensor was replaced after the engine heated, however the rough idle did not go away I have an issue with my set up. This is caused by the VCT Control Solenoid. This part is from Hitachi and the S/N is scratched off. I don't have any problems with the price or quality, but I cannot say I enjoy the design.
Do not buy junk, I missed the return date by three days so it has been lying on my work bench for a few weeks. In an effort to resolve the issue caused by this defective part, I have had to replace multiple parts at the parts store where I should have bought an auto part with a one year warranty. Do yourself a favor and buy a part with a year warranty at the auto parts store. My heart aches when I hear the truth.