Throttle Body Shop TBS 10201 1/4" TBI Injector Spacer 1986-95 Gm TBI Motors

$ 19.77

Score By Feature

Based on 107 ratings

Delivery

9.06

Satisfaction

8.59

Customer service

8.65

Packaging

8.92

OveReview Final Score

How Our Score Is Calculated

Product Description

With this spacer, the injector assembly on your throttle body is elevated and 15% more air flows into the

The item is sized to fit 1986-95. In 8L 4, you can find a The third lesson is 5L. The rate of 5.0L is the same for all. Several types of vehicles will use this motor, including Silverado Sierra Suburban Yukon Blazer Camaro Firebird Caprice S10 Jimmy Although it will fit 7-liter motors. For the 4L TBI motor, most came from the factory with this spacer, however, it is not required - see your application for details

It comes with extended injector mounting screws and instructions, so there are no gaskets required.

As shown in the photograph, the injector spacer design is subject to change - however, function generally remains the same

As you can see in the second photo, these injectors are usually fitted with TBI pumps

Questions & Answers

Is this going to fit on a 1994 Chevrolet Silverado ?

In the case of a TBI motor, this will fit.

Does the gasket need to be replaced?

By replacing the current thinner injector pods gasket, the spacer will offer improved performance. It is easy to swap out the thin gasket for the thick one and to install it with the new longer screws! There may also be fuel line extensions for the TBI unit that can be found on Amazon.

The part on this page is the right one for the Can someone explain a 4l chevy tb to me? The 7 is the reason I ask. A larger TB unit and injectors are part of the 454 (454 bbc) engine than in the The unit is 7 liters. ?

What you wrote gave me the answer I was looking for! It will not fit, therefore

I do not understand what this spacer is for The one that is included in the rebuild kit is the same size as the one included ?

I am relying on my memory. Not at all. There is twice as much material in this gasket as in a "normal" one. The purpose of this device is to raise the injector pod above the throttle bores, allowing more air to flow over the In the case of the normal gasket/spacer, a plastic material is used instead of the typical gray gasket. It's on my laptop, but I have not installed it yet, so I can't tell you how well The spacer, the yellow regulator spring and matched flow rebuilt injectors will be attached to a spare TBI when it arrives. The throttle shaft has been rebushed, and the intake has been fitted with an Airaid spacer. Since air flow is restricted in this area, it won't hurt to use this.

Selected User Reviews For Throttle Body Shop TBS 10201 1/4" TBI Injector Spacer 1986-95 Gm TBI Motors

There has been a noticeable improvement in performance

5/5

There was a definite improvement in the performance of my TBI 350 ('95 Silverado 4x4) after installing these upgrades. Although its not a miracle cure, I noticed an improvement in the performance of my car at idle and part throttle. This also enhances the launch while standing from a full stop, reports the "Butt dyno. ". The performance / acceleration of the software has not yet been measured since I installed it, but I will do so and compare it to the baseline measurements I made before. As far as modifications to the air filter assembly go, it is essentially stock, except for a free flowing exhaust system and a modified air filter assembly. It took me probably 20 minutes to install (and a definite improvement in the way my truck drives). If I were to recommend something to a friend, I would definitely do it.

Avianna Hatfield

| Dec 04, 2020

I purchased this product when I rebuilt my throttle body

4/5

Delivery was prompt and the product was as described. As for the gains, I did a lot more than that to my 94 K1500. I rebuilt the throttle body, added this and the expensive yellow spring, as well as a helix throttle body spacer with all new throttle position sensors and idle air controls. I love the way it runs! My next plan is to get the new vortec fuel pump, then it will probably run even.

Peyton Floyd

| Jul 10, 2021

It is part of the Ultimate TBI Mods collection, with "Easy" as its main feature

5/5

Installation was easy on my 1990 Buick 5 with no problem. I have 7 traumatic brain injuries. With the gaskets, I was able to lift the injectors even higher, without any adverse effects, and it works better now than ever In the past, I've done the same thing with "ultimate TBI By using the spacer and gasket, the space is raised by 1/4" and there is more It's fine to use the injector spray, there are no problems.

Jocelyn GOUGH

| Sep 06, 2020

It takes no time to install, and it is well worth the money

5/5

I especially liked installing the spacer because it was very easy to do. A TBI air flow thing (looks like a salad bowl) and a 1 inch spacer are highly recommended. This part works great with all the other parts, and part throttle is better in most cases, but full throttle is better for consistency throughout the.

Lyla Hill

| Apr 15, 2021

You don't need to waste your money! Do not waste your money on it *br>And if you return it, you will only receive a small portion of what you spent on

3/5

Justice Bradley

| May 02, 2021

This appears to be a good design

5/5

Trying to get it to fit, but it seems to have a nice fit.

Danielle Hester

| Dec 11, 2020

The surprise was great! I was able to improve my truck with it

5/5

It is easy to install and of good quality (plastic). After installing this spacer and the 1" throttle body spacer, I noticed the improved performance at highway speeds. Visit my YouTube channel to watch my video.

Marshall Sheppard

| Jan 18, 2021

It is rated as a 4

4/5

I have no problems with it. I think this gasket is a good replacement for my old one. There was no noticeable power gain, but on the other hand, miles per gallon increased by half. It would be best to buy this if you need a new gasket.