Bapmic Front 34356789492 + Rear 34356789493 Brake Pad Wear Sensor Kit for BMW 5 Series E60 E61 E63 E64

Bapmic Front 34356789492 + Rear 34356789493 Brake Pad Wear Sensor Kit for BMW 5 Series E60 E61 E63 E64

$ 9.89

Score By Feature

Based on 188 ratings

Value for money

8.88

Easy to install

9.13

OveReview Final Score

How Our Score Is Calculated

Product Description

It is designed for BMW 525i 525xi 528i 528i xDrive 528xi 530i 530xi 535xi 535i 545i 550i

The aftermarket product is of premium quality. A one-year warranty is included

The purpose of the enhancement is to enhance performance. It takes only a few minutes to install. The reliability of this product is high

PWS112, 0841533, 084-1533 are also available as 094-1533, 094-1534, 084-1533, 094-1644.

Questions & Answers

Is this a one kit solution to cover all brakes, or are there more than one I need to order?

For the front, you need 1 brake, and for the back, you need 1 brake

Selected User Reviews For Bapmic Front 34356789492 + Rear 34356789493 Brake Pad Wear Sensor Kit for BMW 5 Series E60 E61 E63 E64

Only 2 of them were for the Are you not sure what the rear looks like?

5/5

Claire Zamora

| Oct 28, 2020

There is a 2008 BMW 535i in our database

3/5

If I had purchased them with my new pads, these would have been included. This set of batteries was a great deal, so I no longer have to worry about alarms. The prongs on one of them were bent, however. I dock a star for this because I'm so used to of wisdom, if they do not go through easy check, they should not push too hard. By gently bending them with a Phillips screwdriver, they will stay straight.

Daphne Hendrix

| Aug 20, 2020

There was a difference between the back and the original

5/5

There are no issues with the front sensors, but the rear sensors are different on the 2007 550i. As a result, the cable from the converter is about 4 inches longer than OEM. If you let the wire hang, it will fray if you tie it up, it will snap. The wire was tied from the inside of the protective connectors cover to the crimping tool. The lighted came on about 2 weeks after the fuses were changed. This sensor shows an almost 2 mega ohm reading instead of a 1 ohm reading. The visual appearance was fine after taking it out. Because the gage is so small, it is likely the wire broke due to being tied up. You must twist and cut the wires to turn off the I'm going to go without a sensor for the time being.

Bruce ASHTON

| Mar 07, 2021

I used this on a 2006 BMW 525i with no problems

3/5

For our 2006 BMW 525i, it was the perfect fit. Wire grommets spaced correctly and locked into the stock fittings had the plugs locked into place, and grommets on the wires also locked into the stock This brake sensor reset the brake service light without any problems. A good deal at a third of the price, but these sensors are not OEM.

Freyja Vance

| Jun 07, 2021

It is an 2008 BMW As it was being inserted into the brake pad, the front one snapped

3/5

The old one was reused, so, as you may have guessed. The rear one has yet to be tested.

Tristan Huynh

| Oct 26, 2020

Despite its good performance, the unit can't replace the original BMW unit perfectly

3/5

At the end, I was able to finish. A little modification was made to the cable so that it can mount to the brake bleeder. There is a kink in the clip area where it attaches to the brake bleeder.

Faye Jones

| Dec 27, 2020

My BMW E60 550I cannot be accessed by these modules

4/5

THROW IT AWAY. I replaced both sensors and had the error code even after doing so. Today I ordered the OCTPY sensors and installed them, and now they work properly with no error codes appearing. I'm sending you back the Bapmic.

Beau Saunders

| Aug 10, 2020

I am pleased with the results

5/5

I used it on my 2010 BMW 535i and it worked fine. Putting the guides in place was a bit tricky because they didn't fit the compartments, but outside of that there were no problems and I was able to clear the.