INJORA RC Rims 4pcs 1.9 Inch Beadlock RC Wheel Rim Set Wheel Hub for 1:10 RC Crawler Axial SCX10 SCX10 II 90046 SCX10 III AXI03007 TRX4 D90 12mm Hex (Black)

It's my first set of beadlock wheels, and I had them put together in no time. They came without instructions, but they're easy to assemble. They look great on my TRX - I am very satisfied with them There was no issue connecting the tire beads to my tires with 4 and it stayed there without issue. In addition to the threadlocker used on the 100 outer bead screws and the 24 hub screws, I used some more on the 100 inner screws. Keep in mind that I won't lose anything when I'm out I don't plan on venting any of these wheels since I have a creek on my property where I play that I would like to use.
These wheels are not vented and that's fine with me, I like to play in the creek on my property. While I would like to see the lock replaced, I hope that the lock is not The ring had grooves on it to hold the foam, but it isn't irreparable with a little glue. I am extremely pleased with what I bought for what I spent. All of the hardware was intact and the screws went together easily. The look great as well.

Jaxxon Bryant

| Mar 15, 2021

For $40 you might expect nothing less than these wheels. Despite its humble appearance, these wheels are quite functional. I installed the Proline Hyrax tires on them and installed them on my TRX4 Sport. I had no issues with stripped or missing screws, and extra parts were When you're looking to buy a decent set of wheels on a budget, these should fit the bill.

Kane Crane

| Jun 12, 2021

It is extremely important to make sure that you have quality RC drivers as soon as possible if you do not have them already. There is an expensive program I use that is well worth it, called MIP. The wheels are now in place. The portals of a Trx-type vehicle will be cleared with these I am putting together a 4 Sport (see photo). A little thread lock on every screw makes assembling them much easier. The cabinets are not difficult to assemble, just takes a little time. method is to line up the screw holes on the back and first attach the foam and inner ring. I then install the front of the rim, then insert the front of the rim, and finally insert the back of the rim. As you put the screw in the rim, press down on the back of the rim with some threadlock. You only need to tighten the threads a little bit, not all the way. Next, insert the screw that is directly across from it. After you have tightened them all in, you can now tighten them down progressively. In the first place, if you tighten that one too soon, it will push up on the opposite side and you will not get it out. Especially the outer ring is tiny, so remember that these are small screws. To tighten these up, you don't have to use all of your forearm muscles. There is no doubt that then you will strip them. It's also a good idea to remove a screw from a hole that doesn't seem right and try another one. Be careful not to push. The only star I took off was because there was one screw that had no threads (see the photo again). Even with that, I was still able to fully assemble the product due to a spare screw in the package.
This is my second pair of Injora beads. I have been pleased considering you spend about half what you would pay for a name brand. I would buy them again if I needed more at this point. One last tip if you need to remove glued tires from rims, boil them. I've had great success with this. As well as acetone fumes, I boiled water and it was quite effective.

Sylvie Arroyo

| Feb 06, 2021

I bought a TRX4 Defender, and I decided to upgrade the rims and I am very happy that I made this choice. I'm not used to bead locks, so it took me a minute to figure out how to install these but it's not hard. It looks terrific on the red Defender with those black rims. Even the stock Traxxas wheels are pretty good, but if you pair them with the proline Hyrax, then you'll have a Spider-type of car This man truck can cling to almost Yes, I thought it would come with 2 larger screws and 4 small screws extra, but it comes with 4 small screws and 2 large screws. Several years ago I dropped a small screw on a tile floor and it bounced in the air, going way out of reach, and is now probably six miles from my house, along with all the other screws I have lost.

Jaycee Sandoval

| Jul 01, 2021

The fit perfectly with the proline bf goodrich krawler ta tires which I installed with dual stage foam and now I have to find a new place to crawl as I can't do it where I used to. Although the tires have been installed, I was surprised how easy they were to do. Initially, I thought I might have missed something but everything went smoothly. I was curious about is if they have air tight valves. The answer is that they don't seem to have air tight valves so venting the tire is not necessary. Anyhow, I never put holes in crawler treads whenever I get the opportunity because that has a lot of torque. I don't want to tear one off.

Johnathan Ayala

| Oct 20, 2020

The nine-inch model has a four-inch screen. A set of Harry Internal Wheel Weights for 1 RC Crawler Wheels with an outer diameter of 7. 4 inches. 9. 2" and 2". The 2" Beadlock Wheel Rims can pull up to 35kg high torque water proof coreless motor with 270 degrees
(.

Kennedy Calderon

| Dec 28, 2020

Extra screws of both sizes were provided (two in total). The convenience of having a spare or two is always nice. It is very difficult for them to slip, no slipping at all. Four longer screws, angled 90 degrees, were used to fasten the ring onto the wheel and the following screws were used to finish the job. The hubs and rings are both blue loctite, but I didn't use it on the rings because of the blue loctite I used on the hubs. There is a lot of room for improvement in the hub depth, so that more of the hex is As of now, they are working.

Kinslee Camacho

| Sep 22, 2020