Wall Nanny - Baby Gate Wall Protector (Made in USA) Protect Walls & Doorways from Pet & Dog Gates - for Child Pressure Mounted Stair Safety Gate - No Safety Hazard on Bottom Spindles - Saver
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The reason they are designed with flat tops and bottoms is because of this very reason. As a result, they can lie flush with the ground, while most similar products require the gate to be raised an inch off the ground. Thanks so much.
Choose a #10 flat top screw that measures 2 inches in diameter. Thankfully, there are two holes in it that allow that to happen. Some gate manufacturers do, however, say that you shouldn't use the gates at the top of stairs for safety reasons, including the risk of a child or baby pushing on it and falling down.
The product is also used to care for my pets. As of yet, I have not found a place where the wall nanny does not work.
Selected User Reviews For Wall Nanny - Baby Gate Wall Protector (Made in USA) Protect Walls & Doorways from Pet & Dog Gates - for Child Pressure Mounted Stair Safety Gate - No Safety Hazard on Bottom Spindles - Saver
Below is a description of the It is easy to install, the rubber grip prevents the gate from slipping, and when removed very little marking is left on the wall. In addition to several different sizes and shapes of wall protectors, it is also possible to install them in different kinds of locations (staircases, doorways, large walls, etc. ) when needed. Depending on where you plan to place the gate, it is essential to choose the correct wall protector. So that's that. Please note
. . .
The following are a few general principles about wall protectors - 2) Wall protectors are not just intended to protect your walls from scratches and dents It's probably unrealistic to expect you won't leave any traces behind that you installed a gate, but there are ways to minimize the damage. However, there is a small risk of dents in the wall thanks to these protectors. 4) With regard to the wall protector, the larger it is, the greater the distance the gate's contact point will have from the adjacent structures such as In the case of a large circular wall protector, the opening where you attach the gate's tension screw is about a few inches from the edge, so the bottom of the gate will be a few inches off the ground. This would clearly create a tripping hazard since the horizontal bar would elevate a few inches from the floor!br>5) Therefore, you should choose the wall protector that gives the largest surface area while fitting within The first round is 1) Gates are 6" in diameter with an opening in the center, into which the tension screws are inserted. benefit is creating less pressure on your walls thanks to their size (which is important for wall coverings like Although they will fit in some places, they shouldn't be used near the floor, where they might bump against the gate and prevent it from closing properly. if you have a large wall space, you can place them on the upper contact points of your gate. The rectangle has three sides 1) Square These protectors fit into places the large circular ones may not, so they put a bit more pressure on your walls than the circular ones. Please note Please note A narrow door frame is configured with the UPPER gate supports vertically. Three factors 1) Dia There are usually about two inches by two inches on them. As a result, these would not be much larger than the gate support. The only place I would use these would be There is no alternative to use at the bottom of a narrow door frame, where there can be no other gate support.
There are a lot of choices between 2 and 5 stars. However, they also left the words "wall nanny" inscribed on the wall in two places at the top. I was able to remove the bottom two, on the baseboards, without any difficulty. At the end of the day, However, I will have to repurpose the space and repaint it.
During the process of screwing in the sides of the gate, I realized that these were leaving an impression on the wall since they were pressing into the In this case, Spackle was used to cover the imprints and paint was used to touch them up.
It is the part that touches the wall where they put the dumb logo.
Dogs can be kept in or out of certain areas of the house with the help of four baby gates. I take care of four dogs - a Bichon, two Pitbulls, and a Blue Heeler - and have to keep the gates up. Their keys seemed to have been unlocked magically! . ) My husband and I were literally putting up the gates every day. Because of this, we didn't want to permanently install the gates, since the areas around the house where we hang them change every two to three Wall Nanny looked interesting, but I thought it was a bit expensive, mainly because I saw similar items that were cheaper elsewhere. A bigger difference is that the cheap pressure points are just round, not as big as the gate pressure points. We had one gate that we needed to keep in place (to protect the cat), so I got Wall Nanny for it and a cheaper model for the others. After three days, my husband (the biggest cheap skate) asked, "Are the rectangle ones (Wall Nanny) more expensive?" I told him yes. Then he said, "Well, I suppose I understand why - " Those Wall Nanny ones can be picked up in a couple more packages. The year is His 16-year-old son tripped and fell into the gate while playing. In the end, the Wall Nanny proved to be the right choice Instead of the gate post breaking, the gate post broke. The presentation was also very impressive to me. (I was not thrilled that my son broke the gate, but I also do not have confidence that the Wall Nanny will keep it.
In my opinion, these so-called When my niece and nephew visited I put these wall protectors on my baby gate it was a quick fix. I'm not sure what the point is. In the absence of flat backs, this would have been perfect. Instead, my wall is now branded with the name of this waste of money.