BOSCH P2R2115TCB Double Ended Screwdriving Bit

The work I do for hospitals is renovation and remodeling. These bits are fantastic if you're a commercial contractor. The bits are in every bit holder that ever went after a #2 Phillips screw that I work with, and that covers a lot of hospital renovations. They are so good at gripping Phillips screws that I use them even in my drywall gun
I was given a bit three years ago and I was so impressed that I bought them immediately. It is estimated that I have driven 200 lbs in steel stud screws in 20-gauge studs and 400 lbs in 1 1/4" drywall screws with these bits. They can also be used to remove or install screws that have a Phillips #2 Having tried all of them, I can tell you that they are all good. As far as impact drivers are concerned, the bits seem to be okay. It wears out faster than a dedicated Phillips bit, but I do not mind. These grip and bite pretty well, so I wouldn't mind bearing early wear for a bit of bite and grip. When you are reaching in a tight area, the last thing you want is the screw to tip over. The bits in this section do not do that. * I have also tried these pieces on screws with a #2 square drive. I find that they are functional. The bits I used for a job when we took apart 8000 sq ft of office cubicles were square drive. To my surprise, the bits worked but the bits wore out relatively fast. As a result, I used a square drive screw to complete the job. Whenever I install architectural door hardware with #2 Phillips bits, both of these are my absolutely favorite I especially dislike stainless steel screws because they can easily get damaged during Whether it's astragal's, push/pull plates, or kick plates that require the screws to be highly visible and look polished, I get the best results with these P2R2 bits and Bosch's 12V Brushless PS22 Driver. This is also due to the great bite that Phillips head screws have on them. We would like to hear from you, Bosch. Both of these deserve to be in #1 and #3.

Oaklyn Simmons

| Mar 24, 2021

I like the idea , it looks good on paper, but my crew run them through a eight hour test, but the test did not last more than ten seconds. Here are the reasons as to In addition to commercial and military projects, we also provide millwork installation services. Assemblage has finally been moved to square drive, or Robertson if you want a more technical description. Our technicians install fillers or scribes in the field, detach and reattach to match the fine work done by today's commercial framers in order to make our cabinets look like they belong Despite the fact that we don't use a stud finder, we still use Phillips self tappers to attach our cabinets to the walls. My mag tips can easily be changed so I can go back and forth between attaching the first cabinet on the wall with Phillips to the first one clamp the second and get my reveal perfect then attach it to the other with the square nib screws behind the hinge plates and finally attach to the wall. These photos caught my eye and I thought what a game changer! Bosch has done it again! Also, I use Bosch for everything! I love their drill sets, hammer drills, chop saws I mean it seems like I use them for everything. I give great word of mouth and love talking people into their tools because if you treat them right, they last forever. Due to the disappointment with these tips and the fact that I am such a loyal Bosch customer, I am going to send them an email explaining why they don't work and see what will happen. Long story short, it's not the best Philips tip and the worst square drive out there. There is no locking joint like most square tips already on the market, so the tip doesn't lock into the hole like every other square tip. It is scary to think that even DeWalt makes a superior square drive. Regardless of who you are or how good some of these people claim to be, you will come out on every single screw. I'm going to try to grind the tips on the tip so they sit well into the square and hope it doesn't adversely affect the phillips side of it. I may also try tempering it to make it stronger, but I doubt it. As a reviewer, I know this is a long post, but at 10 dollars a box, I do not want others to be duped. Due to their incredibly strong hold, I super glue my square drives into mag tips so I don't lose time each day pulling them out of the screw when they pop out of the If you want to buy milwakee square tips for now, until this dual setup is perfected, and because the technology is not at the stage where we can use it, just change out your mag tips in your drill.

Harlow Joyce

| Sep 07, 2020

instead of Robertson No. The screws in the picture are 2. It's much better to use a power drill for me since I'm not very good at it Screws can be driven with an electric screwdriver rather than a manual screwdriver. This is for You can imagine that this was a big deal for me - one deal, IN THE SAME BITE Now there is no need to use, pull out PH2 and replace with R2, and so forth. As long as this part remains in place, I can continue It saves me a great deal of time.

Sawyer Murray

| Jan 10, 2021

Compared to standard #2 bits, these bits are considerably better. This type of grip has a better grip and does not break or wear When you are working on an airplane, they are great for removing inspection panels. The number of worn-out screws I had to drill out is now reduced. The additional purchases will be made when they are.

Lucia Meyer

| Dec 22, 2020

It is incredibly important to use these guys to install electrical devices. During the install process of (especially Legrand) devices, they have square and Phillips tip together so that they catch screws. Although they break fairly easily, they are worth it in the end.

Liam Meyers

| Mar 22, 2021

The wrenches have proved to be very useful for unstripping and removing stubborn screws without stripping. I was skeptical at first but they have proven to be reliable.

Stefan Hudson

| Apr 21, 2021

Roberson & Co, #2 Philipps will be ranked #2. Plugs and switches should be used for this product. They're brittle, so you can't use too much torque (like when you drive in a long wood screw). The rest of the time, they are perfect.

Emelia Schaefer

| Mar 20, 2021

The screwdriver works great with almost all Phillips screws that the average person might.

Scarlett Wilkinson

| Mar 25, 2021