Handheld Shower Head Holder, Angle Simple Brass Shower Handle Holder, Bidet Sprayer Holder, Shower Head Bracket, Hand Held Shower Wand Holder, Shower Arm Holder Wall Mount, Brushed Nickel

It is perfect for the job. We already have so many fixtures built into our shower tiles that it is getting so annoying. Therefore, this little guy manages to hold our shower heads without requiring a lot of bulk. I must stress that the following information is vital Another buyer said that one side may not fit but flip it over and it should work. Top & Bottom will come together fine. There is a difference in diameter between the top and bottom. There is a diameter of 21mm on one side, and a diameter of 23mm on the other. There is one shower head hose that doesn't fit one of the five shower heads we have. Probably just a little too big for the holder of that particular one. That's okay, I'll replace it after a while when it's broken by a member. It does its job for our kind of facility at the end of the day. We like how small and compact that is, as opposed to our previous holder which was a clutter on our walls. This is an easy to install program. It comes with two screws and two washers The anchors are It was a wee bit difficult to drill holes in the shower tile, but it was better than suction cups!.

Egypt Rocha

| Aug 03, 2020

An easily removable shower head can be found here. Depending on the size, it may hold yours as well. I would never use it for a permanent holder, but for now, it will do the trick. ITS SCREWS INTO THE WALL/STEEL SIGNAL SLOT OR SURROUND, SO I DO NOT RECOMMEND IT IF YOU HAVE TILE OR SURROUND. Note It is rated three stars in terms of This wall mount does not have any suction. It just screws into place. A quick screwdrive will get it sturdy again after it loosens over time. For a while, it holds well, but eventually, it does loosen. The pros are This is a cheap product. Although it's nice to look at. The installation process is fast and simple. The two screws are in now. A sturdy shower head that holds our shower head nicely. There are a lot of us, and it is The non-profit sector A tiny thing. This is not an obtrusive device. The tapered area in the holding area ensures a firm If you have a need, you may be able to reuse this after replacing. The cons are Suitable for short-term use only. There is a limit of only 1 screw per screwdriver. The enclosure or tile is not present. It takes time for screws to loosen. They don't loosen The problem can easily be fixed. There is a chance your shower head might not fit this model. Half will fit in ours It keeps the spray very steady because the hose has a rubber buffer, but unfortunately it is insufficient to prevent it from squeaking. There is a 13/16" diameter at the top of the hole, so if you have, say, a 1 inch hose, it will probably not.

Brennan Snyder

| Feb 27, 2021

It is not what I wanted there was no supply for the model I wanted. Therefore instead of paying more, I took the simple route and went low-cost. Metal holders are very economical and simple. • This is a good solution. Con //) *br// It would be nice if there was more body at the back of the sprayer holder so the handheld sprayer could sit farther Getting simple is good for most applications it should work. The bottom line is that this works well and should last, but I'll keep an eye on the finish to see if it.

Jesus Craig

| Apr 04, 2021

I don't think it's bad, but also not great. It doesn't come with a manual or anything to hide Despite seeming high quality, the included anchors are quite low quality and should be replaced with those that can actually resist daily wear. I did not find this to be the worst shower head holder I have ever used, though, for the price it is excellent. I was surprised to find, though, that it does come with stainless steel screws, which are essential.

Onyx Espinoza

| Sep 18, 2020

I tried a suction cup first but heard it falling a few hours later and hitting the tile floor. I didn't want to drill the tile, so I tried this first. This item can be found on Amazon and I immediately bought and drilled it (using a drill bit designed for treating tiles Perfect! I love the look and the way it works! *Brushed nickel finish on a heavy duty brass fixture. The item is of top quality! It would have been better for me if I had done this before.

Declan Ford

| Apr 29, 2021

The purpose of getting this item was for a hand-held shower head to hold a small shower holder. You have a problem in that there is no angle on it, so your shower head sits in the wrong place In order for it to point down instead of straight out, I had to put a wedge on it.

Lennon McKenzie

| Dec 17, 2020

It does a good job of keeping my shower head in place without moving. If you do not locate the studs first, it is necessary to use the mollie anchors included in the installation kit.

Tinsley Mills

| Mar 08, 2021

The plastic ones were my original plan, but I am so glad I did not get them. I have no doubt that they will do their job for years and years to come because they are made of metal.

Shiloh Gilmore

| Nov 15, 2020