Black U Channel Edge Trim Seal EPDM 15/32" high x 19/64" Wide (5 Feet)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
You can trim your neck by clicking here The blog of Lok
It says that the trim is made out of EPDM, an extremely durable synthetic rubber The rubber is synthetic and resistant to weather. The heat resistance of EPDM resin depends on the resin manufacturer and grade, but As an example, Exxon says their EPDM resin can handle as high as The material's continuous range probably fits well with what you are trying to do. This range is suitable for use
Despite fitting well over sheet metal, the trim I purchased would not work with the thicker plastic you are using to mold the dust cover. Check out the profile of the edge to have a better idea of the quality.
An inner fender panel that is 3/16 thick was used with it and it fit perfectly
Selected User Reviews For Black U Channel Edge Trim Seal EPDM 15/32" high x 19/64" Wide (5 Feet)
I used them to cover the outside edges of the fenders on my utility trailer, from which I had cut the 1" down-facing lip to increase I liked its pliable texture and how well it covered the edges. Please take note As described in the description, the trim does not have any adhesive. Initially, I believed it would be tight enough for me to wipe it down and forget it, but it wasn't. It broke easily when hit by road bumps, people brushing against it, etc. Simple fix You might want to finish it off with a thin coat of Lexel adhesive caulk. During the six weeks since it was installed, it has held up well Before it needs to be replaced, I anticipate several years of use before it needs to be replaced.
I bought this product to cover the edge of my cage doors to keep me from being scratched by the cage wire but it did not stay on properly and kept falling off. I would have preferred something maybe a little thicker and more to hook onto my cage wiring little disappointed in this product.
Despite the thickness being the same as shown in the detail picture, the material did not seal when going around the same sizes of curves as it is described in the specification. These items are likely to end up in the garbage and I will not buy them I bought most of the edge trim and weatherseal I bought and they didn't work as advertised. My next Amazon purchase will not be anything like this.
I cut these into strips and wedged them between the planks between my deck and the tenant's below. Thus I was able to scrub without dripping water on my neighbor's. There are some cracks where the comb is a little wide, and some where it is a little narrow, but never does it interfere with the scrubbing. A variety of materials prevent water and goo from leaking There is plenty of softness in the product to accommodate brushing close to the crevice without tearing, breaking or falling One or two planks at a time are scrubbed, then the strips are moved from one section to the next. I was happy that I was able to buy a limited amount of product and still get the.
To provide the kids with a mat for their desk chair I purchased 2 hard plastic mats. As a result, they cut their toes on the edge of the mats when they stubbed their toes on it. It was a great idea to try the edge trim around the mat, and it worked Getting it on was tight, and so far I haven't stubbed my toes or cut myself.
The channel seems to be able to fit panels of up to 1/8" in thickness. It was quite good to bend the corners and stretch them slightly on the inside Imagine if you were to make a rectangular hole around it. In corners outside of 90 degrees, the material puckered too much, so I used a mitred cut, and that looked best. Anything much thicker than 1/8" thick panels caused the channel not to lay flat on both sides of the panel.
As you can see, this U It was a pleasure to work with 22 ga and channel edging. Specifically, it was best for the metal project since it was versatile and easy to install on the metal edge, leaving a finished and safe.
The trim looks great. Working with this company is easy. Only down side is that it smells strong, but as long as it's on the outside, it should not persist. It took 35 minutes to apply and was well adhered. I had gotten this to replace the factory trim on fender flares because I had been trying to stick it to them for hours and it would not stay on. The text had to be reworked slightly, but nothing overly.