* Disclaimer: OveReview is reader-supported. We earn commissions from qualifying purchases
Goodman B1809913S Board Goodman B1809913S Board Goodman B1809913S Board Goodman B1809913S Board

Goodman B1809913S Board

Goodman B1809913S Board Goodman B1809913S Board Goodman B1809913S Board Goodman B1809913S Board
$ 95.95

Score By Feature

Based on 216 ratings
Easy to install
9.18
Value for money
8.78

OveReview Final Score

How Our Score Is Calculated

Product Description

Suitable for the Model GDT045-3, GDT045-3A, and GDT045-3B.
The GDT070-3, the GDT070-3A and the GDT070-3B are compatible with this model
Models GDT090-4, GDT090-4A, and GDT090-4B are compatible with this pump

Questions & Answers

How does this compare to the Goodman GMP 050 What kind of guarantee can the seller provide?

The parts listing for GMP050 can be found here As a direct replacement for this control board, it is easy to install.

Can this be used for a Gmph075- What's the difference between furnace 4 and furnace B?

Thanks for visiting. It has been a pleasure hearing from you. Your model number matches this one, so you can use that. Whenever you have any other questions, please do not hesitate to contact me. you, I really appreciate it!

Can it be used with the B18099-control board ?

The problem should be fixed. This is the board I've got

I have a goodman control board with model number B18099-B1. Thanks for reading If my board is out of date, can this board be replaced, and how does it differ from 13 without an s is the same as 13 with an ?

You are welcome. Thank you for the With the B1809913S, the older B1809913 has been replaced with the updated B1809913S.

Selected User Reviews For Goodman B1809913S Board

The board in my 15 year old Goodman air conditioner started clicking (the natural gas side was trying to turn on while the air conditioner was running), but in the summer I normally shut off the gas
5/5

After a few seconds, the exhaust fan turns on and runs for a little while before it All the usual "I hope this works" tricks such as tapping on all the relays in hopes of some connection sticking worked. In addition to turning off the power to the unit, I had to unplug and replug every connector. did some research using the web to find a solution (don't take the first thing you see as the answer) and I found reports of a similar problem and I determined this controller board might be the answer. In comparison to making a phone call to a service company, paying the hundred fifteen dollars was a reasonable One of the problems I encountered was the wiring from the thermostat did not To give you a sense of what I did, I compared the colors of the standard connectors on the thermostat and this helped me. As soon as I snapped a picture with my cell phone and wrote it down on a notepad, I verified the power was The money you save might not be as great as you think if you do not understand how to turn off the power. As much as possible, I unplugged each device independently and replugged it in a convenient location. As soon as everything was plugged in, I looked through my notes and photos. It seems to have all worked after I put the parts back into place and pushed in the interlock button. Although it was summer, I turned on the natural gas and verified that the heater would work (even though it was summer) so I would not be surprised by a winter surprise on the heater. I turned off the natural gas again and checked the A/C again. The outside unit works well, but I'm planning to replace the start capacitor and relay in the Perhaps I will have 20 years left with this old unit before it breaks down. Buying this board turned out to be a good investment. I have read where some generic boards did not turn out so All of you who leave reviews are appreciated. Here are some tips I hope will help you.

Dior Crosby
Dior Crosby
| Jan 20, 2021
The program is very easy to use
5/5

I cannot blow the outside fan on my air conditioning system. There was no fan on the outside of my AC unit, and I tried the following before seeking help Replaced both capacitors, checked if the fan starter relay worked, checked the remote was working, and measured the voltage at the remote control. There were no results. The board arrived by USPS on June 23 after I ordered it on June 20. The board was replaced by a Texas Instruments B18099-based board Those who are 20 years old would be in the class of 13. Since Resistors 1 and 7 were burnt, I decided to replace the whole board rather than just replace the resistors. I did have to restart all the power supply, and then I had to restart the cover panel switch. The configuration is slightly different, so make sure you read the cards. There was nothing particularly difficult about it. The wires I had to connect and disconnect The circuit is connected as follows cool, heat, HSI, IND DFT, BLK, 2 transformer wires, 4 neutrals, W/G/R (one each) and a 9-volt There are six pins on the In the event that B18099- is not being replaced Check the manual before wiring the 13 board. It may be a bit different than the 12 board.

Lainey Gallegos
Lainey Gallegos
| Jun 07, 2021
Perfect! Just what I was looking for
5/5

There was an issue with my furnace that randomly cycled the fan or exhaust fan even when the thermostat was The unit plugged in one or both of the fans, ran them for a few minutes, and then shut them off afterwards. The periods of interruption would last for a few minutes or several days. The standard gas furnace is not too complicated, so I assumed this must be the problem. I am not a heating or air conditioning guy, just a handyman An independent contractor. I was able to change out the unit easily and it was It was easiest for me to transfer one wire at a time on purpose to avoid mixing I've had no problems with it for over a month now. In comparison with hiring a contractor, I am sure I saved many hundreds of dollars.

Jett HILTON
Jett HILTON
| Feb 11, 2021
I saved a couple of bucks by using this
5/5

I am very pleased with the outcome. It was pretty easy for me to do the attic installation on my own, since I'm quite handy. I thought the instructions were quite good, no matter how different they were from the card that it replaced (later revisions). No hitches, fixed my AC problem perfectly and I was happy with the outcome. We have been using the new unit for about three weeks now. By doing it myself, I was able to save several hundred dollars. A few of the wires needed to be removed and discarded, but a new set was supplied Also included in the package are new plastic stand-offs to keep the card from being broken. Using a simple complexity scale, 1 is the most complex Based on a score of 10, 10 being "call a pro", I would rate this as a 4 You need to check with the place where you have the unit. In case you are not comfortable around electricity or don't know how to shut off the power, you should hire a pro to take care of it. As you pull each one off the old board, label them as you do so. If you do tackle the task yourself, take a few pictures of the wires from various angles before you start pulling them off. It is also a good idea to make sure the wires are fairly clean before taking pictures, so you can tell the color when you The color of blue and gray appear almost similar on a dirty wire in a dark environment. On mine, the old and new spade lugs were not located in the same place, so be aware of that as well.

Willie Buckley
Willie Buckley
| Aug 25, 2020
It's so nice to have a cool air conditioner! Install is fairly straightforward, but there are some details to keep in mind
5/5

It is VERY important that you do not remove the old board without a replacement in hand! By doing this, you run the risk of placing wires on the wrong connectors on the new board and possibly damaging it. Best practice Identify the problem first then fix it. Get a new board by clicking the link below Replacing the old board (wire for wire) should be done only when you are ready to install the new board. It is a quality piece, and we now have air conditioning and heating!.

Anaya Baird
Anaya Baird
| Sep 25, 2020
It is unlikely to be received on time
3/5

As I believe USPS lost this part in transit, I don't know why it took so long for me to receive this part. In any case, I decided to replace my furnace because the Goodman one I had was a lemon and I was tired of replacing the flue pan annually. likely, because it is made of a type of plastic, there is a design flaw which caused it to crack. While the part of my old furnace did work, I wasn't using it at the time, so I couldn't tell you how long it would.

Sterling BYRNE
Sterling BYRNE
| Oct 26, 2020
Surely it will last a long time if I am not receiving this board but another one made by ICM
3/5

My last board I had never worked, but this one does, but the other failed in a different way. It will be interesting to see how long this lasts. In the first case, we waited 13 months, and in the second case, we waited 6 months. Getting this board was the first time I got it from them. I hope it works for a long time. It started out as a Goodman board and lasted for.

Stanley DOHERTY
Stanley DOHERTY
| Jul 26, 2020
does not match actual product
3/5

It is not a Goodman brand circuit board, as indicated by the picture and description. In the end, it is an icm280 board and you can find one for much less This board will also require some mods to your wiring if you intend on using it.

Zaid Wiley
Zaid Wiley
| Feb 15, 2021

Related Products For Goodman B1809913S Board