Broan SR169016 Aluminum Filter Spring Kit (Pack of 3)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Three of these are included in each pack Per filter, there are five clips. Do you think it is a good fit If you wish to determine the answer, it may be easiest to remove your current filters and verify that you have a 3 clip system with 1 clip shared between the two I do not have the ability to answer your compatibility question because my filters are a different number than your 99010301.
Neither a screwdriver nor a bit is included.
No matter how they look, if they are the same, it is a good deal.
Metal is used to make the spring clips for the filter.
Selected User Reviews For Broan SR169016 Aluminum Filter Spring Kit (Pack of 3)
REMOVE THE RIVETS BUT DON'T REMOVE THE LOCK RINGS! Since both sides of the center one were broken when I first moved in 11 years ago and another side has recently broken, I thought I would try these since both sides of the center one were broken when I first moved in and another side has now broken as well. Since I'm not a fan of duct tape, my screens have to be in place before I can begin. * My ), so I bent and broke off the remaining bracket 1/2. The rivets were left intact, the adhesive attachment points were washed and dried again, the areas of the new rivets were placed with alcohol, and then I re-cleaned and dried them. Then, using a pair of scissors, I poked a hole in the adhesive where the hole is on each bracket, peeled off the protective paper, pressed the bracket over the rivet, and put the screen in! We have a deal. Oh, and the frames have notches cut out to hold the screens in place, so if you feel the front of the hood where those are matched to, there would be two notches made of the metal of the frames. I used some metal and bent the frame back to flatten the notches after many years. I gently placed some metal inside the holes and gently pushed it into the holes so they are no longer bent inward. Earlier today, I noticed that the cabinets no longer fall out when I close them. Since most of my goods are metal, I'm sure I'll never need to replace them.
For the installation of these clips, you do not have to remove the existing rivets. The first thing you need to do is break off and remove the old plastic clips, leaving the rivets in place. After that, you clean the area around the rivet thoroughly to remove all grease or dirt. The third step is to peel off the backing tape behind the new clips and press them over the existing rivet(s). As the existing rivets pass through the clips' holes, the adhesive backing will adhere to the existing rivets. Then put the filter screens back on and allow them to sit for 72 hours. You should not prepare anything with high moisture levels during this time. As soon as they have set up, they will feel very attached to each other. Thanks a lot!.
It took minutes to install these and they were a perfect fit. The old dead broken rivets were removed, and the old rivets had to be drilled out. We used rubbing alcohol to clean everything. Those clips have adhesive pads, so as well as hooking them up I also inserted a few low head screws. The whole thing took me no more than ten minutes, and I was I believe that the OEM clips were made out of a crappy ABS that made them brittle. I observe that they are made of a nice spring metal and appear to have been coated in some way. This was not only easy to replace, but the new part is also much In addition to the replacement screens, I also bought the finishing touches for the project, and I am very pleased with the finished product. Do both at the same time.
These are great! I'm very happy with them. My hood was originally furnished with plastic clips that were riveted in place. These clips are much better made. It was as simple as drilling out the original rivets and putting pop rivets in their place The new rivets need to be inserted into the old It wasn't comfortable to use only double faced tape over a hot stove surface for a long period of time. Only for the reason that installation might not have been that simple for someone who lacked the right tools I deducted a star.
We used to have an old Allure QS1 that these fit perfectly It is a fan that vents air. The old rivets that held the plastic clips in place are replaced with holes for the new ones. It was convenient to poke a hole in the double sided adhesive with the tip of a small screw driver to enable easier installation. In order for the adhesive to stick to the hood, it must be grease-free, and the provided alcohol pad wasn't even close to being sufficient. The denatured alcohol I had on hand cleansed the grease very well. I soaked paper towels in it and swiped at it with a finger.
It is fine to use these in place of the originals. According to the instructions, you should carefully remove the pins that remain in the unit after the hinges have been snapped off, but I did not The existing pin went through the untape on the STILL UNTAPPED sticker holding the new hinges in place, I pulled out the sticker, removed the bit of stuff in the hole, then took off the tape and voila! Since the hinge is centered, and the pinhead holds it in place, it will be secure once I'll make it easy for you. I completed the project in less than one minute.
These springs were purchased for a hood filter on the range top. Since the filters' clips were broken, they were inaccessible without first removing the entire hood and screwing in new clips in the marble behind the filters. It wasn't clear if the adhesive backing on the Broan springs would be able to keep the filters in place. four months after installing the filters, the filters are in place securely. After applying the adhesive backing to the back of the hood, the whole process took less than five minutes.
It was very easy to install these clips on our overhead stove hood after receiving them. The clips come with double-sided tape that is used to cover the rivets. I applied the tape to the rivets over the existing rivets. In my opinion, the clips seem to hold and I didn't have to drill and install a screw as specified by the instructions (the replacement kit came without screws by the way). The double-sided tape worked perfectly for me for the first few weeks, so I will have to drill and add a screw if it breaks in the future. The clips work great and I would recommend it for customers who need to replace.