Hornady Lock-N-Load AP Progressive Press Shell Plate
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Hornady part number 392645 indicates that it is the shell plate for 45 ACP (#45 for 45 ACP). I'm not sure how the image is related to that part number, or its
The picture on their site is the wrong one. There is no shell plate visible since the picture is of a Hornady shell holder.
With a Hornady Lock n Load progressive press, it should work. The EZject system is available there as well.
Selected User Reviews For Hornady Lock-N-Load AP Progressive Press Shell Plate
Good quality from Hornady when it comes to doing its job. You may run into problems such as cases not aligning with station 1, cases tipping, not ejecting, etc. You may want to verify that your shell plate Initially, I had no problems resizing cases, but after a few instances I began having issues. The screw in the press shell plate is more like this (rather than shell plate screws walking out). A 3/8" lock washer can be added if this happens and it should be tightened down gently (but firmly enough). Be sure to put the lock washer on top of the washer to prevent the shell plate from being gouged. That's the case. An example of a shellplate screw head is shown below. You are reading A lock washer is a device for opening locks You are reading There is a washer in your house You are reading An armor plate.
I love these things in general, as well as the LNL system in particular. The spring’s leading edge rests on the leading edge of the corner which is why this one is so costly (see photos). In addition, I had to modify the leading edge of each corner, which is irrationally tedious. prevented the spring from sliding under the edge that the spring glides on in position 5 to hold the shells in place, instead of sliding inside into the groove that allows the shell to eject in position one, allowing a new shell to be inserted in position 2. The solution I used was to use an orbital sander with a 220 grit disc and to carefully round off the leading corner of each potition (see photos) until the spring fed under the shellplate reliably In between tests, I removed a small amount of material so as not to remove too much material, in case of any unintended consequences. I have not yet encountered any unintended consequences. Any errors that result from this modification will be updated as soon as possible. As a whole, the plate works fine, and it only took a few minutes to get the work done. Have a happy loading experience!.
This is a good solid plate overall. I had some issues with mine where the cases were seating on the plate extremely hard. When I inserted a case, about 60% were binding in the extractor groove when I inserted them. The following would be happening for everything from militaries to A broad range of brass will be offered, from specs for Lake City brass to commercial parts for Winchester brass. There is no rhyme or reason to it. In lieu of contacting Hornady for a new plate, I used a file and sandpaper to remove just a small amount of material from the bottom side of the plate to allow the cases to slide into it It should be noted that these plates are made from a very hard tool steel, which is difficult If you have trouble inserting your cases, go slowly and gradually remove the material from the plate until your cases are easy to insert. Once your cases are easy to insert, you can clean them up with The spot I am referring to is on the shell plate and if you purchase this shell plate, you will know where I am referring. In terms of Hornady's customer service, I have MUCH doubt that they would not have replaced the plate for free if I had called them.
First one I had to send back because it did not work properly in my press, and I couldn't find a way I got the second one almost as fast, but it had a similar problem As of the fourth position, the fourth position was not locking into place. However, I was able to fiddle with the second one to get it to work.
A high level of quality is taken into consideration when creating these things. It's difficult to find a bad one nowadays, with the technology we have today.
A brand name will become yours once you commit to it. There you have it. There are a few steps involved. Hornady shell plates were available at the best price on Amazon, as of the time of Taking the time to shop around pays off. Thanks a lot!.
The shell plate I ordered is from Hornady . At the time, it was hard to find, as it was in the A progressive press had five shell cases in the shell plate that I ordered. I was able to use it flawlessly. The index was placed where it was supposed to be. Despite the fact that midsouth did not have one, my price was the same as what midsouth would have offered. There were rumors that I would have to weigh for a long time in fact, I saw the results after just a week or so. In the photograph I am reviewing, the press is a single stage, which is not what I am reviewing.
As for the product, I have no other comments to make about it other than that it has exceeded my expectations. With my new Hornady AP press, the plate fits quite well. After a shell has been seated, it discharges the loaded casing and completes the 5 cycle set. No faults are found in the product, and I am happy to own.