* Disclaimer: OveReview is reader-supported. We earn commissions from qualifying purchases
SeaSense LED Switch Panel 6 Gang with Breaker and Rubber Boots SeaSense LED Switch Panel 6 Gang with Breaker and Rubber Boots SeaSense LED Switch Panel 6 Gang with Breaker and Rubber Boots

SeaSense LED Switch Panel 6 Gang with Breaker and Rubber Boots

SeaSense LED Switch Panel 6 Gang with Breaker and Rubber Boots SeaSense LED Switch Panel 6 Gang with Breaker and Rubber Boots SeaSense LED Switch Panel 6 Gang with Breaker and Rubber Boots
$ 48.39

Score By Feature

Based on 120 ratings
Easy to install
9.72
Value for money
9.38
Water resistance
8.58

OveReview Final Score

How Our Score Is Calculated

Product Description

To cut out, measure 3 inches by 5 1/4 inches
With a push of a button, resetting the breaker
It comes with mounting hardware made of stainless steel.

Questions & Answers

Is it possible to modify the sizes of circuit breakers?

Split sizes are not available for No

The fuse on the wire is a big fuse. What is its size?

As far as I know, there are no big fuses. On the other hand, if it is the master fuse then I would not worry too much about The fuse size you need depends on what system you have. When all of the speakers could run at the same time you need to figure out the total amount of amps that will be pulled by the switch box. Your fuse needs to be a bit bigger than your total amps to protect against short circuits. It is possible that a fuse that is too large will not provide adequate protection. When the motor starts out, it pulls more amps than when it is running at full speed. Check the size of the motor to determine its capacity before you buy one. If you want to test your system with a fuse value, you can assemble your system, then test it with that value. My desk is too far away from the office to go check, but I would like to go. Keeping arthritis at bay.

What labeling is present on the switched? My goal is not to use this in a boat, I rather want to use it on ?

There are labels, but you can always print your own using a label maker or something, or you can just add extra stickers over your current labels.

Selected User Reviews For SeaSense LED Switch Panel 6 Gang with Breaker and Rubber Boots

BE SURE THE PLASTIC FILM HAS YOUR LABEL ON IT SO YOU DO NOT HAVE TO PEEL IT
3/5

Please be warned! A factory release states that the plastic film is part of the weatherproofing and should not be removed. There are 12 WP boots that cannot be removed so as to peel the film due to the soldered buss bars. It seems that the W/P boots will not do. The LEDs are encased in plastic so they will not be damaged by moisture. However, Seasense also felt the need to put a plastic film on top. The package does not state that plastic needs to be removed. Protective plastic film is often included on electronic devices that must be removed before they can be used. Two, the spare labels are a complete replica of the originals, which means you only have 12.

Dior Trujillo
Dior Trujillo
| Mar 22, 2021
It has been installed and is working well so far
5/5

My contender 23 has been installed and is working so far. A six-month hard running period will be followed by an update at the end of the year. I have updated The fuses on my panel keep tripping on my saltwater washdown pump and my large bilge pump. My pumps must now be wired through separate dedicated switches. I have updated Still going strong as of summer 2019.

Kyrie Decker
Kyrie Decker
| Aug 30, 2020
There is no problem
5/5

It is currently being installed (wired). The screws that come with the panel make installation very simple. An additional ground buss would greatly enhance the installation. I installed the ground buss separately and it makes the installation far simpler. It is nice to have an indicator light so you know if the circuit is working.

Finnegan Reynolds
Finnegan Reynolds
| Oct 31, 2020
Panel for switching on and off the boat
5/5

I like the fact that it is easy to trim and can fit into existing holes. There is only one thing I wish that were different, and that is the overhang should be 1/2" wide to allow for over trimming to be In any case, it worked as expected and was very simple to wire in.

Lyric TALBOT
Lyric TALBOT
| Sep 10, 2020
Due to corrosion, it hasn't held up well
3/5

In less than 2 years, the switch panel has failed, most of the switches are no longer functional due to corrosion, and the LEDs work or not depending on when they are turned on. In spite of always being covered, my boat does sit outside every now and then. I am ordering another because the panel size is correct and it's only After I finish, I'll see if I can bump it up to 50.

Abraham McIntyre
Abraham McIntyre
| Aug 14, 2020
Wiring and switching on my boat were made very clean and easy with this device
5/5

Wiring and switching on my boat were made very clean and easy with this device. It would have been better if I had purchased one with additional switches since I will be upgrading it after fishing with it a year.

Leia Kelly
Leia Kelly
| Feb 11, 2021
A simple process of installation is required
5/5
Gideon Holmes
Gideon Holmes
| Dec 01, 2020
Changing it up will help
4/5

I really liked how you set up this site. The money would not cover the cost of buying all the pieces separately. Installing the device is straightforward.

Paloma Phillips
Paloma Phillips
| Apr 19, 2021

Related Products For SeaSense LED Switch Panel 6 Gang with Breaker and Rubber Boots