JRV Products A8976RBL Rocker Switch

$ 13.24

Score By Feature

Based on 129 ratings

Delivery

9.47

Giftable

9.64

Value for money

9.45

Customer service

9.56

OveReview Final Score

How Our Score Is Calculated

Product Description

15 inches are the length of the package. A diameter of 24 cm

There are 5 inches between the package's top and bottom. The diameter of the wheel is 8

There is a 20 cm width to the package. The length of the glass is 32 cm

It weighs no more than 0 grams. I weigh 0,45

Questions & Answers

In addition to depth and hole, what is the actual size of this switch? From the photos in the review, it's impossible that the ones listed are accurate. ?

There is a raised bezel that is approximately 12 mm high. Five sixteenths of a meter by three metres It has a diameter of 7/16 and a depth of 1/2 inch. The wires you are going to use need about a 1/2 inch hole behind it.

Is the switch plate cover and switch plate a neutral color or is it a darker shade?

Black is the color of the cover plate, the bezel, and the screws. White is the color of writing

Can this be surface mounted rather than cutting a hole in the panel if you carry a bezel to put this on?

There is a bezel on it.

What is the number of prongs on the back of the JRV Products a8977rbl rocker switch?

The switches are each divided into two. The power is on, the power is off.

Selected User Reviews For JRV Products A8976RBL Rocker Switch

The installation process was more challenging than I had anticipated, but the product works fine

5/5

The item is available in three pieces, if you'd like to know what you will receive. In the rear of the switch is an outer frame or bezel that raises the switch about 3/4 inch above the surface. Upon opening, notice both that there is a flat plate that has screw holes and a rectangular cutout where the rocker switch is located. Lastly, there is a rocker switch that clips into the flatplate. About one inch is the length of the back of the rocker switch with its electrical connector. There is a 5 inch clearance from the back of the mounting frame to the back of the connectors, which means the mounting depth cannot be reduced. The first thing you need to do is To mount the switch on the wall, drill a hole of 25 inches in diameter. To create the needed diameter mounting hole with a step drill, I planned to use a 1 inch drill bit, but on my trailer there is only 1 inch of depth between inner and outer walls, which means that a 1 inch drill bit won't work. A hole of 25 inches in diameter is too long to drill through the trailer's wall as well as its outer skin.

Brianna Trujillo

| Sep 13, 2020

The price is high, but it is worth it

5/5

This switch was recently installed in my travel trailer for switching between an exterior step light and an interior companion light. Although the installation was straightforward, I did not install the large plastic bezel because I need the switch to be as flat as possible since I mounted a companion light above it.

Alora Daniel

| Feb 19, 2021

Switches that work well

5/5

At the moment I am using four of these to convert my cargo hauler. It appears to be sturdy and of a nice size.

Cayden ALLAN

| Dec 24, 2020

It is the perfect repair for me

5/5

So far, this seemed to work well for me. It met my needs exactly.

Janelle Mercer

| Jun 10, 2021

I like it a lot

5/5

To finish off a custom trailer in a clean manner.

Kyro Blankenship

| Dec 05, 2020

I like how it looks and it works, but it is rather This is a pricey item, but looks well and works as expected

5/5

In fact, I just ordered a second one for my motorcycle trailer interior cam.

Saylor Hubbard

| Jul 06, 2021

This is perfect

5/5

Ideally, the switch and bezel should be of good quality. I purchased this component to add an extra accessory circuit to my camper. The factory original looks like it came from the factory.