It is possible to get six sizes of ring diameters due to the length of the screws, and the pictures you'll find in this listing are all the maximum rings' diameters.
With a matte black finish, it is made of solid aluminum
Design Rail Types Picatinny/Weaver 2 Piece Design for Clamping
Aluminium barrel with a diameter ranging from 21mm to 34mm diameter range 21mm to 34mm
Hand pistol, rifle, shotgun, and rifle mounts can be opened by means of a flashlight or laser
Questions & Answers
What is the best way to attach it to the mag tube or barrel of the Henry Big Boy 357?
To answer your question, I looked at the Henry big boy 357. I would say the distance is too close to draw any conclusions. The barrel and tube are not in much contact with each other. This is a great mount for the price. It would be purchased, but I would not buy it if it were not a good
Do you think there is a possibility to install these back to back and get the same result?
It might be possible to define a rail based on the length of the barrel if that is possible
Selected User Reviews For VERY100 Hunting Universal Single Rail Picatinny Weaver Barrel Mount with 3 Slots
I have tested this on (Mossberg) Maverick 88 12ga with great results
This is attached to the magazine tube ahead of the fore stock and underneath using the longest Taking the clamp half and sliding it through the space between the magazine tube and barrel was no problem. After tightening, the screws protrude about an eighth of an inch (through the rail piece), so perhaps a slightly larger tube or barrel could be used. Fortunately, it fits snugly to the Maverick 88 and does not interfere with pump performance. After mounting an inexpensive green laser on it, I used it to mount another. The combination of the two is compact and solid, and the laser is protected to some extent There was a nice kit of extra screw lengths for smaller diameter holes as well.
| Nov 11, 2020
It is a really good product
What an awesome device this is. 3 screw sizes make it possible to fit barrel diameters ranging from 1/4" to 1". On an air rifle made by Gamo, I am using it. I have a bi-fold folder that I can attach The device allows you to attach a laser sight or a tripod to it, and switching between them is effortless. Put this on and tighten it down, and it is solid you don't need to move it Bid on a good deal instead of a cheap one There is no benefit to using them. If you get this, then any bi-directional camera will mount A rail mount for a picatinny tripod.
| Dec 17, 2020
The rails work great when I attach my Victor Spyder paintball rifle barrel to the rails
The Victor Spyder paintball marker I have has a cheap front foregrip that I would like to add. In addition, I have used the feedtube in a configuration with the feed tube offset to the right by about 30 degrees so that I can add a red dot sight that is not covered by the feed tube.
| Mar 13, 2021
The diameter of the outside of the gun barrel is fine, but make sure you measure the inside as well
The screws are sufficient for anything from 12 gauge up to and including a 30 mm barrel however, if you are shooting anything around the 1 inch range, you will need to buy them separately, as the longest screws provided were not long enough to attach to a 30 mm barrel. On the top of the page, the images showing the measurements don't take into account the fact that the rail is in a diamond shape, so it must be measured between two opposing contact points, not from top to While the rail itself is good, but it would have been great if it accommodated more than a 30mm barrel. Overall, this is a good buy at the price, but since it was described as accommodating more than 30mm barrels, it does not truly live up to that description.
| Sep 21, 2020
The Maverick 88 is not compatible with this
As far as I can tell, this mount is of excellent quality. It is unfortunate. Unfortunately, it does not fit at all in my Maverick 88 magazine tube. In the end, when I could not make it fit my gun, I looked at the order and noticed it was a barrel mount, not a magazine mount. The error has been corrected. You can find product information by reading the.
| Jan 11, 2021
Designed to fit Ruger Mk II My old ruger (bull barrel) doesn't have a rail because it hasn't been drilled and tapped yet
It was too tall to clamp on the rail from sun optics. The price was reasonable, so I decided to give it Putting the stock on top of the receiver, mounting a $30 red dot sight and firing it off I gave it a try. I was very happy with the result. After working itself loose a bit, I tightened it up so that it would stay in place-even after a second round of shooting. There was a slight forward movement, but not enough to lose 0 points. The scope is front heavy, but I can see fine at indoor ranges with it. This is a good (and cheap) alternative to gunsmithing.
| Dec 01, 2020
The following is my brother's - A recoil gun that belongs to my lawful father-in-law Upon looking for a way to mount a sling on the 16 gauge he wanted to hunt with, he found he needed to permanently alter it
As a result, I was worried about it interfering with the front sighted bar. I was not able to see it over top of the receiver when sighted. The rig was completed with sling mounts through QD quick disconnects attached to picatinny rails.
| Oct 09, 2020
The barrel mount is very good
The item has been received in a timely manner. I liked the fit and finish of the suit. A Mossberg 500 shotgun barrel mount can be attached to a flashlight to make it easy to use it. You can mount a flashlight, laser or other accessory to the barrel of your shotgun with this option.
| Mar 15, 2021