Jugs containing five gallons of undiluted juice A formulation that cleans inks, coatings, adhesives, varnishes, and resins in a safe manner
IPA is a great alternative to 3D printers that use isopropyl alcohol (IPA)
The product has a low VOC content, conforming
A minimal level of personal protection is necessary
Surfaces of indirect food can be cleaned safely because they are NSF registered
Questions & Answers
How long does it take to separate UV resin after it has been cleaned in an ultrasonic cleaner? Is that the case, in what way?
First, allow the solution to be exposed to UV light for a few minutes, to cure any remaining resin bits, and then filter through Yellow Magic 7 left behind something that can be reused.
Toner in laser printers can be cleaned by this product?
It is not recommended to use Yellow Magic 7 to clean laser toners.
The adhesive side of a clear tape had some black grease on it. What are the chances of this cleaning product destroying the adhesive after cleaning off the grease?
If you want to use Yellow Magic 7, I would not recommend it. As a result of its design, it breaks down UV and water-based compounds A wide range of inks, coatings, and adhesives are based on acrylics.
Do you know if it can be sent by air courier? Could it be transported in an air courier system or is it flammable?
It is possible to send Yellow Magic 7 We are not able to offer air transportation via Please feel free to contact us directly by dialing The number is383- The air transportation order can be set up by calling 8465.
Selected User Reviews For Yellow Magic 7: One Gallon, Full Strength, Undiluted Jug of Human and Pet-Safe Flexo UV Ink and Varnish Cleaner for Food Packaging, SLA 3D Printers, Coatings & Varnishes, Rubber, Plastic, Steel
You can really see the 3D printed parts after cleaning them with YM7
The reason I started using it was because I was using 91%. In post processing of 3D printed parts from my SLA resin printer, I utilize this tool. It is very easy to clean printing with Yellow Magic 7. To homogenize it, pour the contents of a 250ml glass beaker into my Branson ultrasonic homogenizer, and drop the entire beaker into the machine. You can really see the 3D printed parts after cleaning them with YM7. The reason I started using this was I would get white patches on all of my models even using 91% Alchol. The alcholol had a high water content, and I think that caused the reaction. We found a solution to the problem using YM7. I love this product. I always recommend it to my friends and family. ABOUT ROBERT.
| Oct 20, 2020
In regards to resin 3d printing, this is the holy grail
As soon as I used this post printing cleaner, I decided there was no other one I would ever use. As soon as I print a model, I swish it in a "dirty" container, and then my ultrasonic cleaner also uses this container. You can slowly drip resin into it and it becomes little spheres that sink to the bottom. It is the weirdest stuff. As a result, the resin does not mix with it since it isn't a solvent. In spite of this, each print prints well without any white fuzzing, and without any other untoward effects.
| Mar 12, 2021
It is now no longer necessary for ISO
I made a couple of errors with this. My first mistake was thinking it was making my print sticky, but then I learned to just leave it in for another 30 minutes after the sonic bath. It was so sticky and yellow that I took it out at the end of an hour, washed it with dish soap and water (even with my fingers), and the yellowing and stickyness disappeared. There is just no need to wait for it to sit in the liquid for too long. Anyhow, this in a sonic bath has saved me from using iso in a bath that can stink up everything and be The smell is a little strange, but it isn't that bad, and it is much better than resin and ISO.
| Jun 14, 2021
This tint is yellow - Used as a replacement for isopropyl alcohol The printing of 3D models
had to go looking for In my search for a solution, I found this 19 shortage) to clean my resin prints with. My research showed it to be promising from the description and from a few minutes of reading. Unfortunately, I did not expect it to perform as well as it did. My experience with the solution is that it leaves a yellow tint on the print and it does not remove all the uncured resins. Cleaned with 91%-ethanol, the print is significantly more sticky than if it had been cleaned with 91%-ethanol Alcohol with a concentration of 99% isopropyl. It is only recommended to use this as a cleaner if you plan on priming However, for the additional $50 in shipping charges, it is not.
| Apr 05, 2021
The cleaning solution doesn't work on 3D prints made out of resin
This product does not work as a substitute for isopropyl alcohol for cleaning UV resin 3D prints, despite the manufacturer's claims.
| Aug 25, 2020
I really like this product, when I use it on the 3D It will impact the clearness of your prints a little more than standard isopropyl alcohol, but it isn't toxic nor flammable
Take care of your eyes. It sometimes turns the excess resin blue during removal of it, which is normal and won't stain the carpet. My favorite part of the product is the packaging.
| Dec 12, 2020
3D resin prints are easily made with this tool
How to clean resin prints by using yellow magic 7 cleaning solution. The action of rinsing in isopropyl after 20 minutes in the ultrasonic cleaner has worked well for me. Although I wish I could loosen up completely and stop using isopropyl, prints remain tacky if I don't rinse them.
| Mar 30, 2021
The stuff you are using is excellent for the application it is intended for
The stuff you are using is excellent for the application it is intended for. However, if you wish to avoid alcohol rinse when using a 3D printer, this is usually not the case.
| Sep 19, 2020