Twidec/Output Single Phase SSR Solid State Relay 25A 3-32V DC to 24-480V AC SSR-25DA

Twidec/Output Single Phase SSR Solid State Relay 25A 3-32V DC to 24-480V AC SSR-25DA

$ 9.99

Score By Feature

Based on 128 ratings

Value for money

8.79

Customer service

8.54

Packaging

8.92

Giftable

8.72

OveReview Final Score

How Our Score Is Calculated

Product Description

Here is the product name Relay system with solid state Please enter the model number. The SSR The heat sink and fan are the things that need to be added to reach 25A

The current situation is that In 25A The frequency of the occurrence is The frequency should be 50 or 60 Hz The voltage at which the device is powered The 24-hour time period The following special attention is needed 480vac If a relay is to be operated for a long time at more than 10A, it must have a separate heat sink configured in case the actual power consumption exceeds 15A.

To control voltage, set the following voltage The voltage must be 32VDC The diameter of the mounting hole is The size of the blade is 5mm/0. The 18-inch range

Approximate size (in square meters) The dimensions of this box are 58 x 45 x 32 mm. Three bucks x one dollars. This piece measures 8" x 1.1". long (using long measurements) The following materials are needed Parts made from metal, plastic, or electronic devices

This is the net weight Here is what is in the package Relay solid state - 1

Questions & Answers

This device requires a certain amount of power. What is the power input?

There are almost all SSRs with a 5-year outlook The input voltage of 32 VDC draws about 9 mA at 5 VDC, and the current slowly increases to about 10 mA at 32 VDC. A current of 5 mA is available It draws a little less than 10 mA at 12 VDC.

The dc side of the circuit draws how many amps?

A large number of SSRs with a 5-SSR have a 5-SSR The input voltage of 32 VDC draws about 9 mA at 5 VDC, and the current slowly increases to about 10 mA at 32 VDC. A current of 5 mA is available It draws a little less than 10 mA at 12 VDC.

Do the relay mounting and heat sink mounting screws come with the kit?

It appears that the mounting screws are not there, but the screws for the heat sink are.

Can you tell me about DC current requirements?

A large number of SSRs with a 5-SSR have a 5-SSR Using 32 VDC input voltage draws about 9 mA of current at 5 VDC, and it slowly increases to about 10 mA in about 2 hours. A current of 5 mA is available It draws a little less than 10 mA at 12 VDC.

Selected User Reviews For Twidec/Output Single Phase SSR Solid State Relay 25A 3-32V DC to 24-480V AC SSR-25DA

Switching on the 240V won't take place until 3 p

3/5

m. The voltage is 6 volts. Raspberry Pi cannot be used directly with this device. Definitely one of the best solid-core games out there. According to what I understand, it appears to be a state relay. Pumping 38 amps through a resistance element at 240V will not be an issue for this device. If it is going to run at high amps, it needs a heat sink and active cooling to prevent overheating. A five out of five for all of this As expected, this was an excellent performance. There would be a 4 out of 5 There are no specifications or datasheets available for this product. On the label it says it may turn on at 3VDC, but it will not. Managing a reasonably complex wiring setup, I spent a great deal of time troubleshooting to find this as the problem. After you have reached 3, the LED will illuminate, but no current will flow until you have reached step The voltage is 6 volts. Consequently, GPIO pins on a Raspberry Pi cannot control the relay directly. In order to enhance the voltage or use a different relay, you will need to add an additional subcircuit.
The other review in which it is stated that the trigger requires a lot of current is either incorrect, or it is At 300, the relay triggers and draws a current of 0. 2 mA. The voltage at which 6VDC operates Current of 4 mA.

Leilani Leonard

| Apr 10, 2021

The device works well, but requires more than 3 volts

3/5

If driven directly from the GPIO port of a Raspberry Pi, this SSR will not be completely turned I have a problem where it will turn on for half a cycle, but not for The problem can be fixed by driving at a higher voltage. An optometrist was just able to see me this week There is a 12VDC isolated output on this unit, which works fine. However, if you are using this via a microcontroller, you may need to increase the voltage on this output.

Nyla Skinner

| Sep 17, 2020

The cover has been scratched up

3/5

It's not brand new, but the clear plastic cover of this SS Relay has scratches all over it. There is also a strong smell, like that of very cheap perfumes. The unit hasn't been hooked up yet, so I cannot test it. This will be lowered from a 3 to a 1 if it fails.

Kira Estes

| Mar 13, 2021

I really like it

5/5

This works exactly as I expected, and I am using it on my 3D printer with a 750W silicone heater powered by 24V from the printer's board.

Carter Guthrie

| Jan 17, 2021

Classic relays are not as good as this

5/5

My original plan was to use a good old mechanical relay, but these ones are much safer and easier to use. The driveway heating mats should be placed in a series with the sprinklers so the wires can be connected to each other. We plan on buying more for other projects as well.

Lyanna Fischer

| Sep 15, 2020

Save your time and money by not wasting them

3/5

To drive radiant heat through the floor, I used this product to take advantage of excess solar electricity. I tried it several hours later, and it failed. The led light would come on, but the circuit would remain closed, so the inverter would eat the batteries' energy. I would have spent thousands of dollars on batteries if I had done it myself. If I were you, I would say it's total garbage.

Siena Brock

| Aug 13, 2020

There is no way to make these No one of these works even though I purchased 4 of them

3/5

A bench power supply has been used with every voltage range I have tried, but the devices will not power I can see the light coming on during 3v, but no more. As soon as they are on, they are drawing. A voltage of 01 amp. My first thought was maybe they needed to have a load on them so they would turn on, but even with a 240v AC load on them they will not turn.