Drill America DWT54028 #0-80 UNF High Speed Steel Tap Set
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
This is the beginning of a collection. Taper, plug, and bottom taps are all included in this set. One set of three taps
The hole is present in most taps of 1/4" and larger. This is to make room for a tap guide; on smaller taps, you can leave it in the handle, which typically has this feature. Also, if your tap doesn't work for some reason, toss it into your drill press. This is a good alternative to simply turning on the tap. You can also chuck the tap handle if your chuck is big enough. I hope this has been of assistance. Best wishes to you. Continue to be cautious.
Greetings, 1/4" There are four flutes in a set of twenty taps. Thank you
To answer the question of 1 piece vs. 3 piece, a taper, plug, or bottoming tap will be sold as a single piece. If you purchase a tap set, you will receive three pieces: one taper, one plug, and one bottoming tap.
Selected User Reviews For Drill America DWT54028 #0-80 UNF High Speed Steel Tap Set
The product photo shows threads wider than the body so you can tap both sides of a tube with a single tap, which irritates me because it does not accurately represent the product. The product received did not resemble the image. I would not have placed an order for them.
I asked for a substitute. In two days, I received a second shipment to Amazon's credit, but it was incorrect once again! This time, I received a similar three compartment plastic flip top box with an identical label containing three IDENTICAL spiral point taps, none of which should have been included in the set! I attempted a second replacement request, only to be told by the system that Amazon could not accept it at this time!! It's not like this is a difficult task. PLUG TAP, BOTTOM TAP, TAPER TAP = 1 SET OF TAPS AS SHOWN AND DESCRIBED. Each of these taps has a purpose, which is why I ordered this item in the first place. Is it possible for us to get this right, everyone? Obviously, whoever is packaging these items has no idea what the differences are. If you're still not sure, look at the pictures in the listing and compare the items to them.
These are fantastic for machining brass. The H value for pitch size is not listed on these taps; for example, H1 is. Each value is multiplied by a factor of 0. 0005 inch over the nominal pitch diameter. 0. 0005 of an inch A H2 or H3 value is used for the majority of taps. These 4 flute, hand taps, a tapping block is recommended, get any tap sideways, and good bye tap appear to be H3 work very nicely and you can't beat the price. Because the shank diameter is larger than the minor diameter, you won't be able to tap past the end of the thread; you'll need special taps for that, which you won't find here. Professionals do not guess pitch sizes, so this tap set is ideal for hobby work.
I required a tap with a threading depth greater than the shank. That's exactly what the ones depicted in the image would do. The 1/4- The 20 taps that were delivered are not going to be used. These taps, however, are well-made and should serve a variety of purposes.
I required a quarter of a On my boat, it took 28 taps to refresh the threads on the stainless steel hardware. A quarter-inch bolt was used for the hardware. The pieces of railing are held together with 28 set screws. I was given a box with a 1/4-inch hole in it. 28 taps. After re- I discovered that the set screws wouldn't go all the way in after tapping the holes. Then I examined the faucets individually. All three were in the quarter-inch range. Instead of 1/4-inch taps, there are 20 of them. After I'd already put them to use, horrors.
"HSS" and "12-" were written on the taps. 24". On the taps or the packaging, there were no other indications of the manufacturer or country of origin. Is it possible that they are fake? What is to be expected? The good news is that they have the correct pitch and diameter, and they can cut soft metals at least. Given the low cost of these taps, this is most likely a good deal for occasional use. They worked fine for the thread cleanup I did, but I wouldn't use them in a production setting.
Cheap sets from mass retailers are fine, but for some jobs, having a taper tap, a regular tap, and a bottoming tap all in the same size is essential, and most cheap sets only have regular taps. I still use my cheap taps, but when I'm working on something unique, such as a steam engine kit, I order one of these sets in each size I'll require.
In a 16-year-old car, I bought these taps to clean out the Frame Rail Weld Nuts. The goal was to install a new trailer hitch, so there was a lot of rust and road grime. br>br>When they first arrived, I was pleasantly surprised by the attractive divided case they were packaged in. Especially given the set's low price, it's very practical. This project's good will come to an end at that point. br>br>The first two snapped in the first nut after only a few minutes of use. This surprised me because I was wearing a T-shirt. You can't get a lot of torque with a Handle Tap Wrench. Because the third Weld Nut lasted for the rest of the project (6 more Weld Nuts), I'm guessing these had a bad temper or were from a bad batch of steel. br>br>Next time, I'll pay a little more and get something of better quality.