Simple Houseware Over-The-Door/Wall-Mount Ironing Board Holder, Bronze

" A Phillips head screwdriver was all that was required to assemble it. It does not take longer In addition to the ironing board, I have a water bottle and a starch in there, as well as my Y leg ironing board. Slamming the door can cause it to wobble, but for the price, it's worth it. Don't close the door too fast. Thank you. I'm very pleased with your service. The cover I bought from Amazon was also paired with a padded ironing board cover.

Justice Flowers

| Sep 16, 2020

The iron I own has a split base/heel, so I needed a holder that allowed the handle to fit around it. Additionally, I wanted a holder to fit the spray bottle and starch. There you have it! All of the above is achieved with this. The fact that my iron has special needs and the space for all three is incredible! As a result of its convenience, I use the ironing board instead of my bed to iron now.

Jaliyah Delaney

| Jul 29, 2021

The hooks on my "Y" leg ironing board were too wide to fit the legs, so I had to hang it upside down. The design is a little awkward but the result is good.

Georgia Bond

| Sep 02, 2020

Originally, I wanted to return the product, but I decided to keep it and modify it so that it would You may be able to do this with cheap $10 irons, but certainly not with finer It was not designed to accommodate larger irons, so I would not be able to use my iron with this product. I am giving you an example of what I mean if you look at the photographs. A falling iron is caused by the fact that it cannot sit flat. It should have been made to be open all the way to the bottom instead of being rounded like it is, the design of the product does not permit the cord to be inserted. Also, when installed, the part that sticks out over the door sticks out about 1/2 inch from the door. The over the door hook part on this was rebent into a smaller shape and I modified it to fit the door (also as shown in the photos). One third of an inch thick is the width of my door. Added holes to the top of the hooks while I was at it so that it could be attached to the top of the door so that it wouldn't move as the door was Aside from that, I feel like the product is pretty durable and shouldn't need to be modified. It takes me less than half an hour.

Nathalia Atkins

| May 14, 2021

In the past, another seller had sold me one which I returned, because I wasn't able to fit the iron inside.

Cyrus Lake

| Aug 12, 2021

In order to ensure that the legs of the ironing board are held shut when closed, the customer needs to be aware of where the latch A latch was located at the back of my ironing board - next to the shelf. So the only way I could handle the ironing board was either from the top or from the The ironing board began to open while still hanging due to the excessive stress on the latch. The legs constantly came out as well as the ironing board. After taking off the shelf and hanging the ironing board from the back end, I began to attach the shelf to the broad end of the board. When being hung, the ironing board has a latch to keep it latched. In addition to that, I'm also concerned how long the hooks, that hold the ironing board, are going to last. When I hang the ironing board, the hooks will spread, resulting in stress feet on my ironing board are the kinds that spread at an angle like an "A" rather than in the traditional "T" the "T" shape were in place, then the hooks on the ironing board wouldn't deflect as much.

Kinsley Mitchell

| Jan 20, 2021

I found this product to meet my needs very well. My intention was to use it on the back of an interior bedroom door, so before ordering I checked the measurements in the description to make sure it was the right measurement. As a result, the board does not hang too low due to the measurements I took. A screwdriver was all that was necessary to assemble the product, which could then be hung over the door with just four screws. As soon as I hung the board with Y-shaped legs, I confirmed that it cleared the floor without any issues. Additionally, I have confirmed that I am able to close the door without any difficulty. This product worked well for me, and I am glad to have discovered it.

Kaia Williamson

| Aug 02, 2021

There was an issue with fit of this Hamilton Beach 19901 iron In more precise terms, it will not reach all the way to the bottom of the cradle. A binding is formed where the iron is widest, and the cradle base sits flat on it. Having described this problem, I solved it by placing a 1' piece of custom-fit foam on the bottom of the There was no need to bundle up everything for return, I just didn't want to deal with it. There have been questions about the ability of the facility to hold V-shaped explosives These boards support the leg. There is a very slight chance that it may do so. There's no science to the assembly, and it's as good as it should be.

Yusuf Marsh

| Oct 17, 2020