T-fal Pressure Cooker, Stainless Steel Cookware, Dishwasher Safe, 15-PSI Settings, 6.3-Quart, Silver, Model P25107

The bottom of this device was separated when I purchased it less than a month ago and spilled across my kitchen. There was a lot of trauma and it was There was a great deal of stress and burning in my body.

Cali Guzman

| Feb 26, 2021

As with many other reviewers here, my pressure cooker setting ring wasn't calibrated when I got it to the advertised 5/10/15psi settings. 3 was probably closer to the truth. Five of eight. Thursday, March 13. It is my dream to be able to breathe at 15 psi and many of you are as well. It turns out that the spring on the setting ring is a little undersized This is powerful. Please see the instructions below for complete instructions on how to raise the settings. TLDR, take out the string and stretch it a little so that it will fit your needs. With more tension on the spring, the easier it will be to push on the valve, which will allow the steam to escape This is *br/*br! An important note of caution! In this case, if you stretch out the string too much the pot might run over its rated pressure when the pressure setting ring is set to something higher. Please be careful as the two other safety features might kick in and keep you from getting hurt or anything. This is
br>- Instructions on how to do it 2. *br. To remove the pressure setting ring, follow these steps You should be able to remove the lid from the unit by pressing down all the way on the setting ring, then turning it past the exhaust setting. 1. 2. The tabs are as follows You will see two large holes on opposite sides of the large back piece after pulling the red ring all the way down. The Picture shows (See Image)*3. To remove the small black piece, remove it from the bottom To hold the small black piece onto the two large holes, two tabs or clips are located at the top of these two large holes. Your fingernail can be used to pop out the tab or clips. As soon as both clips are removed, the small black piece will pop out to reveal 4
Spring with an extended length The length of the spring after no pressure has been applied is shown below. If it is not under pressure, pull it gently until it is a bit longer when it is not under pressure. It will be harder to maintain high pressure settings when there is no pressure on it for a prolonged period of time. Note that 5. Take into account Organize everything back into its proper place. Thank you, Nathan.

Madalyn Armstrong

| Apr 18, 2021

Sadly, the lid handle of the cooker just broke when I opened the lid, six months after I purchased it, and I tried to gain warranty on it, but, according to the Manufacturer, the warranty is only for a year. During my phone call with They failed to fulfill their 1-point promise There is an 800 number, but I had to wait a long time to talk to their representative and she said the warranty only covers the pot, and not handles or It is definitely sketchy practice for your warranty to cover only POTS lines. In the future, I would like to go with Presto or someone who has a 12 year warranty and clearly states what they cover.

Eileen Blair

| May 30, 2021

The shirt I purchased was a T-shirt This is the P25107 Six from Fal. A 3 quart pressure cooker was purchased on July 22, 2016, and has been used about 15 to 20 times since then. After that, it would no longer be able to hold pressure. When I ordered the new gasket, I thought that was the problem, but no. It turned out that the gasket under the pressure indicator button was damaged. In my phone call with the company, they stated that although this is a rare occurrence, they do not consider it as a manufacturers defect and do not In addition, due to liability concerns, I cannot get the part and have to send the appliance in for service. I will replace my appliance with a presto stainless steel pressure cooker. As much as I enjoyed using the product while it worked, I could order a different product that is comparable for less than the shipping and service costs of this one It is bal. There is no need for me to fix it It is quite distressing for fal to not know why the gasket disappeared in the first place, only to have it.

Sage Brock

| Aug 19, 2021

Initially, it seemed that it would not create a pressure seal when it first started. However, after about 3 months, it continued to not work. Then it seemed to increase in frequency, and it was never certain whether it would seal or not. I thought it was probably our user error since it wasn't all the time. The screws on the handle of the chair were loose, my wife noticed. Due to the screw heads being on the inside of the lid (see photo), this must be resolved as soon as possible. In the end, we had to tighten them because it appeared that was possibly the place where the plastic inner piece (see picture) wouldn't My email to T- was sent after 10 months I provided proof of purchase to fal, and they requested it. When they received the form, they said that I would have to send it to them, and they would decide whether they could use it or not. After that, if any problems arose, they would fix them. they do it once and it seals, especially since we just tightened the screws again because it just did it once. I hate to bother you like this. The decision to deal with it has just been made. If you get this motherboard, I recommend that you pay the extra for the no hassle warranty by Amazon so that you can just return it and get another one. Maybe it was just us. I wouldn't mind buying another one if it wasn't what I wanted.

Wilder Perry

| Oct 25, 2020

At 12, the vents open. A PSI of 8 is required. This is of no use to me. There is a T-shaped curve A 404 web error indicates that US contact information is missing on the Fal web site. Despite having a good appearance, if you can't exert the pressure you paid for, then the product is worthless. This purchase is regrettable given the lost time and product as well as the loss of time associated with it. I intend to return it after first use.

Judson Nelson

| Dec 12, 2020