T-fal Pressure Cooker, Pressure Canner with Pressure Control, 3 PSI Settings, 22 Quart, Silver - 7114000511
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The T-shirt I have is one of my favorites It is a P2510737 model. There is no pressure canning with this unit. It is only for pressure cooking. One very important point is to let the steam vent for a few minutes before closing your unit to be certain you have a good seal. The new models are so much easier to use than the old ones that could overpressurize. In the instructions, it was not clear how to do it, but from pressure canning, I knew how to do it.
Unfortunately, it doesn't measure up to expectations. My review can be found here. The situation is different than in 2013, but it was not the same in 2018.
A stainless steel unit is a stainless steel unit
The new one comes in an 8-quart size.
Selected User Reviews For T-fal Pressure Cooker, Pressure Canner with Pressure Control, 3 PSI Settings, 22 Quart, Silver - 7114000511
The bottom of this product has separated and spilled all over the kitchen in a month since I bought it. A traumatic event occurred and it was very dangerous. A lot of stress and burnt were present in my body.
I, too, experienced the same problem as many other reviewers on here when I got my pressure cooker ring which was not calibrated to the advertised 5/10/15 psi settings. There were more like three of us. The fifth part. The 5/13 date. It is my goal to reach 15 psi, as is the wish of many of you. spring in the setting ring is slightly under tension, which leads to the problem I am empowered. The full directions are beneath, but TLDR, you should take the string out and stretch it a little bit so that it will rise up to your desired setting. If you stretch the spring even further, it will be harder to push on the valve, so it will let the steam out at It's a wrap! A word of caution! *If you do this and stretch the string too much, the pot's pressure setting ring might be set to an amount above what it was intended to be. Hope the two other safety features kick in and you don't have to worry about anything bad happening to you, please Please read carefully
- Follow these instructions to get the job done 1 *br After the pressure setting ring is removed, follow these steps Turn the ring past the full exhaust setting and press the pressure setting ring down all the way. The lid should pop out of the machine. 3.
To show the tabs, expose them as follows The red ring must be pushed all the way down to expose two big holes on opposite sides of the large backpiece. The picture shows (See Picture)*3. The small black piece can be discarded as follows Each of the two large holes is equipped with two tabs or clips that hold the small black piece in place. By tearing the tab/clips apart with your fingernail, you can remove them. As soon as the clips are out, a small black piece will protrude from the opening, The fourth paragraph. A spring that is elongated Take a look at how long the spring is at its current length before you apply any pressure. Pull it gently until you reach a point where it is somewhat longer when there is no pressure. If it is left without any pressure on it for a long time, you will have to increase the pressure setting. This is 5. Put back together All parts should be reassembled. Nathan, cheers,
.
After I bought the cooker, the handle broke off when I was opening the lid - just 6 months after it was purchased. The manufacturer says it has a 1 year warranty, so I tried to claim it. T called me when I was on the phone They failed on their first attempt There was a long delay before I could reach a customer service rep at the 800 number. She said the warranty only covered the pot and not the handle or This is a sketchy practice when you have a warranty that only covers In the future, I will purchase a Presto product or a product with a 12 year warranty that explicitly states what's covered.
When I purchased the t-shirt, it read It is the P25107 of the Fal company. It is highly likely that you have used it between 15 and 20 times in the last two years since you bought the pressure cooker. It would then no longer have the ability to hold the pressure. A new gasket was ordered thinking that was the cause, but that's not what happened. It's the gasket under the pressure indicator button that came loose. It was explained to me when I called the company that while it is a rare occurance, it is not considered a manufacturer's defect, so they will not pay for In addition, as a result of liability issues, I cannot order the part, I must send it in for service. As a replacement, I will order a presto stainless steel pressure cooker. When this product worked, I enjoyed using it, but I could order a Betterment comparable replacement for less than the shipping and service costs I was paying on this one while it worked The falcon. There is no way I am going to fix it This is the second time Frank has made the same mistake without knowing why the gasket disappeared the first time.
The problem started off nicely. However, after about 3 months, it didn't seem to be able to create a Our first thoughts were that it was probably user error since it was not always the case. Then it kept increasing, and you never knew if it would seal correctly. The screws on the handle of the cabinet were loose, as my wife noticed. Because the screw heads are on the inside of the lid (see the picture), this is a problem. Our plastic inner piece went on just fine except for the area where we tightened them because it seemed that was where the seal wouldn't work (see photos). My email to T-D was sent after 10 months of waiting The first thing they asked for was proof that I had purchased the merchandise. They told me I would have to pay the shipping costs to send it to them, and they would decide if the file would be OK. After that, if there were any problems, they would be fixed. It's possible that they did it once and it sealed due to the fact that we tightened the screws again just a few minutes ago. I don't understand what the fuss is about. It just turned out that that's what we needed to do. I would recommend that if you buy this, pay the extra for the no hassle guarantee by Amazon so you can just return it and get a new one. I would recommend adding a couple of dollars to the cost for the warranty so that can be done promptly.
A vent is located at 12 o'clock. There is an 8 PSI pressure. I cannot use it for what I need. This is the T (404 web error) The Fal web site has no contact information for the United States. It looked well made, but if you can't create the pressure you paid for, it's not worth the money spent. My intent is to return the product after the first use, but I regret this purchase and the lost time and product it represents.