InnoGear Webcam Stand, Upgraded Flexible Desktop Stand Gooseneck Stands Holder for Logitech Webcam C922 C930e C920S C920 C615 C960 and BRIO and Other Devices with 1/4" Thread
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
My experience with using the camera as a dslr is a slight angle and as a better webcam. The stand can certainly hold the camera, but please make certain you keep it balanced by making sure the bottom is heavy since a heavier load may cause the stand to tip over. Since my camera (Canon T7I) isn't super heavy, I do not add any weight to the bottom of the stand.
Mounted on a screw and ball, the camera looks as though it's floating It consists of a socket that is tightened with a This gun offers quite a bit of flexibility in pointing, but you have to make sure that it is pointing where you want it to The tightening screw needs to be removed. If you have a camera with some tilt capability, you will do better. There is a Logitech C920 on it and it works pretty One thing I wish was different is that I did not wish the goose a happy birthday It would be better if the neck were My best solution when I am writing is to write "around" the stand so I can point the camera at the page. It works, but it is not ideal.
All I can tell you is that cameras have a standard thread type
Those cameras appear to have a monitor mount, and I did not see any mounting holes on them. 1/4-inch hex key allows that mount to be removed from the camera If you have a 20tpi thread, it should In case you have a bigger camera with a threaded hole in the bottom, the same 1/4"-26 thread is probably used there too At 20 tpi.
Selected User Reviews For InnoGear Webcam Stand, Upgraded Flexible Desktop Stand Gooseneck Stands Holder for Logitech Webcam C922 C930e C920S C920 C615 C960 and BRIO and Other Devices with 1/4" Thread
Do not be harsh, only You can either fix the flaw yourself or do your best to avoid using these, but they will get the job done. There is a longer shaft near the center of the base than the base itself. By putting all the way down, you will cause the center shaft to slip out of It is supported by a plastic ring that guides the shaft inner If it falls off, it could get damaged. There is a whole shaft that screws into the base (do it yourself on arrival) and the threads are fairly easy to strip. In order to resolve both problems, I did a A bit of wood was welded into the hole of the lower shaft to stop the inner one from falling out when the base is welded to the bottom.
It has a weighted base to keep it steady, an adjustable height pole, and an integrated bracket for mounting the webcam. The flexibility of the additional neck lets you adjust the camera angle and height. If you plan to produce a video with a close-up camera view or a wide-angle lens, do so in the content Overhead of what you are doing, this seems to work well with web cams that are smaller & less powerful A GoPro can even do the trick. If your camera or lighting is also heavy or long, it may not be possible to use a flexible gooseneck. Although it holds my Note8 at an angle using a phone camera mount (not included), the weight of the camera mount seems to be pushing the product. My standing desk is a convertible type, so I need to be aware of the placement, height, and size The angle needs will depend on how close the camera is to my face (so it does not show up my messy room) and whether or not I am standing or seated. In my previous attempt at mounting, I had tried a goose neck mount that clamps onto the wall, but it did not work well with According to my needs, this seems to be a good solution. Also, I can put the product behind my monitor so that it is out of my way when not in use. According to the images I provided, my monitor is 27" and the bottoms sit approximately 8" off the desk. So you can see that this is a ton of height for a desktop monopod. To date, I have no complaints about the product and am happy with my decision. Finding something I like has finally occurred to me ).
There is no doubt that this camera stand is of high I was surprised to learn that the base was made of cast iron since it is so simple to assemble out of the box. This is a very strong and sturdy model. I purchased this stand for use during live stream sessions, and it is perfect for that. We moved around a lot less, our S camera is no longer wobbly. In the event that you found this review useful, please hit the button below, and I thank you for taking the time to read it.
When the goose neck is attached to the camera and the goose neck is at a right angle, the stand is top-heavy. My return was due to the fact that it falls over with a simple tap.
When I first started, I was using a gorillapod that I had available. It was adequate, but it did the job. I switched to a standing desk after I swapped my old desk, and in doing so, I was trying to maximize the available desk space (my home office is in a small corner so my desktop is 42 x 24 inches). In that sense, it was important to get everything mounted to the edges and off the surface, thus I secured a gooseneck that clipped to the edge for the webcam. In that case, the gooseneck was too long and very stiff, so the challenge was there. The unit handled the task of moving back and forth between my monitors and holding it in place, but it was a pain to move. It caught my eye and I grabbed it after seeing In spite of the fact that it does not meet my one goal of being "off the desk," as it has a solid base and is not clipped on, it works for me because I can move it when I need it. Whenever I don't need it, I can move it to anywhere I like (usually just around back of my As long as there is a trade off, I will take it.
There is a lot to like about this stand. There are no holes in the base, and they have included non-metallic components The bottom of the shoes have rubber skids The addition is very nice. I like the most feature of this webcam, the pivoting head that you screw in to. Many different angles are possible when it comes to angling the webcam. The bending part of the stand should have been about three inches longer than 6 inches so that it would allow much more bending (even though they say it has an 8 inch gooseneck but if you look at the pictures, you can see that only the top and bottom inch can In spite of this, the product is very well made.
The height is appropriate and it can be extended and lowered as indicated. I found it to be inferior to my Logitic C615 webcam (the screw that is used to hold the camera down is missing from the C615 and is in the way so it doesn't provide a solution). If you rig it up, you can do it. The screw should be inserted into the surface all the way to make it flat, it's kind of magnetic, so it should hold, but if you're trying to turn the camera for a Proctored test, you won't be able to.
The program does just what it needs to do. I use 2 of these paired with 2 led rings to set up my stream. You save a lot of money by buying this instead of Elgato There is a weighted base on these cameras that is quite reasonable for a webcam. However, in severe angles, much else will have issues.
Related Products For InnoGear Webcam Stand, Upgraded Flexible Desktop Stand Gooseneck Stands Holder for Logitech Webcam C922 C930e C920S C920 C615 C960 and BRIO and Other Devices with 1/4" Thread
