HP J7961G - Jetdirect 635n IPv6/IPsec Print Server
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
In addition to the 510N and 620N cards, both of them can run at up to 100 mbps and work with most 5000 series printers. It makes no sense to buy a 635N if you are not going to use its 1000 mbps capability, so you end up wasting
The admin section of Explore is available to you
Selected User Reviews For HP J7961G - Jetdirect 635n IPv6/IPsec Print Server
Recently, I started experiencing network interface problems with my HP2420dn. The firmware was updated to the latest version (20120113 08) in order to fix these issues. The four HP products from HP are listed below. A few hours after the update, the internal NIC went completely out of commission. As a matter of fact, unless I disabled the interface, the printer would halt before initialization was complete. In the near future, I discovered that my very old 3Com switch was not functioning. My only knowledge is that the switch failed to cause the NIC to fail or the switch went down because of the NIC. Whatever the case, I replaced the switch and installed this 64-bit EIO JetDirect NIC (635N). This seemed like a good solution to the problem I was having. The vote did not occur As of now, I still had 49 different items. This results in error xxxx. The problem seems odd to me, but as I investigated it, I noticed a few A quick look at the Windows driver for the printer showed that it had 128 MB of RAM (it had only 64 MB) and that it offered choices between 128 MB and A second change comes as part of the firmware update, the printer's RAM Disk option has been set to AUTO (I had always turned it off before). Initially, I suspected that my "memory problems" were caused by a small amount of memory not sufficient for the new firmware and EIO NIC requirements. By removing the RAM Disk, I saw improvements but not a complete resolution of the problem. In order to resolve the potential memory problem, I installed a new 512 MB DIMM in place of the 64 MB I see that the printer has now been restored to normal operation. Even so, the internal NIC still causes the printer to halt before initialization is complete, so I leave it switched off. Here is what you need to know if you have a similar issue The old DIMM in the printer was removed, so it is possible that, in spite of it always passing the initialization self-test, but I do not know what happened to it It was the DIMM that was bad and caused the problem during the test. It is possible that the Windows driver expected the printer to have more memory than it actually did, which could have caused Windows to write too much data to the printer overwriting firmware memory. There is a possibility that the firmware upgrade did not install correctly due to lack of memory, and this failure is causing the NIC issues. It is likely that the problem was related to the Windows 7 standard Microsoft driver since I employed the latest HP print drivers. In any case, the printer has been working without errors for several weeks, and I appreciate the new NIC very much.
Our HP Designjet 111 needed exactly what this item had.
With the HP DesignJet 111, we have a powerful new tool that will be essential to With its original installation, we had it installed near a print server and used a USB port. With this new Directjet cable, we can now access the printer without using a print server. With the DesignJet on card, we can move it anywhere in the office we need it. As well, the print jobs are printed faster and the client machine can view the status of the printer.
I was having trouble printing with my HP DesignJet and it was getting very flaky. We bought the 635N card after the HP tech advised it was time to upgrade our network card. All our problems were resolved after the purchase. In perfect condition, it arrived on time and worked the minute it was turned on.
I found that this device worked as expected. It would be great if Amazon offered this service for every product. I'd definitely buy from them In order to make sure I met the required amount of words, I have to add this final part.
We didn't have to buy a new printer because of it!.
There should have been some kind of warning that this is not an option on this printer. Just the original printer is the problem with this device.
I had to disable the DHCP for IPv6 though, because I do not run DHCP. There is only one downside to this card it is quite expensive. Laser printers can be found for less now than they used to be.