WGGE WG-009 Banana Plugs Audio Jack Connector 6 Pairs / 12 pcs, 24k Gold Dual Screw Lock Speaker Connector for Speaker Wire, Wall Plate, Home Theater, Audio/Video Receiver and Sound Systems
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
I ohmed them out once I got home from work today. In other words, from the gold banana plug to the silver colored metal jacket, they are conductive. Once more, they fit snugly into the banana plug receptacles on the amplifier, and they are far enough apart that I'm not concerned about them shorting each other. You shouldn't have to worry about them in case you dropped metal on them or something like that.
It is possible. I have a Yamaha RX-180 and it fits perfectly I have an Av receiver V730.
With banana plug setup, this speaker or receiver can be connected to any make or model
Selected User Reviews For WGGE WG-009 Banana Plugs Audio Jack Connector 6 Pairs / 12 pcs, 24k Gold Dual Screw Lock Speaker Connector for Speaker Wire, Wall Plate, Home Theater, Audio/Video Receiver and Sound Systems
They are two separate things. In RCA cables, the centre plug is used to carry the signal, while the outer portion is for the ground. Two banana plugs are not needed because banana plugs have only one connection.

If I could give a 10 out of 10, I would. It has a very easy installation process and is a great design. We used it as a way to connect speakers to a This is how I made the circuit using 14 gauge copper stranded wire. There are no instructions anywhere, so this is how I made it. *Brief description here The wire should be ripped at least for a foot * 2. 2. Remove the center piece of the banana plugs. 3. You can loosen the two small screws now. 4
A little bit of tightening was necessary on the small screws*6. The outer cover and middle part have been assembled. The job is The design is clean and easy to use, and I want to thank the manufacturer.

banana plugs are ideal when you need dual USB connectors to secure the connection - They have dual lock screws per connector. The only gotcha is that they only take main to 8AWG speaker wire. I used 10AWG Oxygen Free Copper dual wiring cable, and they work with 10AWG size, but I recommend not adding a twist on cover that you normally add as part of the process. In real world testing, they are usually such a tight fit that you cannot put on those covers with the red vice black labels because they do not fit over the set screws. It can be either of them. It is so tight I cannot get the identifying covers to slip past the set screws and snap into place because the wire itself fits, but the set screws barely peek out from the tight fit. While I don't have actual 8AWG wire to test, I'm certain that even if you can get the wire to fit and the set screws in place, the identification covers (red versus black) will not be able to be twisted into place, let alone tightened. However, most similar banana plugs that have two set screw screws don't work well with anything larger than 10AWG, and they almost always don't work with anything larger than 6AWG. If at all possible A wire gauge of 10AWG can be used. The price is way too low to pass up the opportunity to buy this set, especially if you got It will be easier to install a wire smaller than 10AWG if you have it. Wire gauges are grouped according to their diameter sizes (the smaller the number, the larger the diameter).

It would have been great if this product fit 8' and up. However, I could not give it a perfect 5 stars because the company claims it should work for 8' and up I tried installing it with 12AWG, but I could not get it to work. I could not get the set screw to sit flush on the end of the wire that was supposed to clamp to the insulation. I could not put the sleeve over the connector since the set screw was protruding from it, which is supposed to press down on the insulator. There were two options left for me. It is possible for me to either secure both screws and then forget about installing the sleeves, or I can install the first set screw and not install the second set screw so that the sleeves can be installed. For my first option, I would like to run without the sleeve as I do not think it will It would be recommended that you use this connector for 16-pin You should use 20AWG if you want to install the sleeve at the same time. However, if you need larger gauges than 12AWG I would recommend looking elsewhere unless you are not concerned about sleeve length.

A last-minute upgrade to my AV receiver gave me the opportunity to upgrade my pins from finicky binding posts to banana plugs, so I decided to look for the most economical and It is my pleasure to report that these solutions meet my needs perfectly. They accommodate wires of common gauges for speaker setups, and they have a well-thought-out design, which provides a firm grip. They are easy to install (caution! You only need to back out the tiny setscrews You can get them lost in the carpet if you take them out completely, and they are also a bit difficult to reinstall afterward). An additional nice design feature is that the outer sleeve slides over the banana tip and is screwed onto it It is a much more convenient method than plug styles, which require you to remember to put the sleeve on the wire before you attach the tips (which forces you to disassemble if you forget). The banana springs make for a tight connection between the socket on your equipment and the banana springs. Even if it requires some work to get them to fit, a tight fit is preferable to a loosely fitting connection which can lead to crackles, pops, and intermittent dropouts (symptoms I've experienced when using weak, poorly made, or undersized cables).

The highest possible quality. I have always had a mystery about banana plugs as to how to wire them. I think this is because of the older style plugs which have you fan out the copper wires around the connector before you screw them In my mind, this always seemed a little half baked. This is due to the desire to have the most copper touching the plug. It is much more logical to use these newer styles. This is due to its small set screw so you can screw the wire down in its entirety. Make sure the copper strands are fully in contact with the plug. These worked well with the new Dolby Vision Compatible DENON receiver I purchased. Essentially, you'll have to pay $2 for each pair of plugs. The only thing you could possibly do wrong is to try. This quick tip might help you. As a matter of fact, the plug is incredibly The signals were very strong, so much so that it would not be able to be plugged into the receiver's input. So you need to squeeze these tips as hard as you can so that they become more flexible. When they were in the ports, they were able to go in easier, but still very snug, which is good because they are making great contact.
