Best Jeep JL Wrangler Hi-Lift Jack Mount kit - Stealth by Dominion OffRoad (Please Read Fitment Details in Description Below)

In spite of that, JL has only one-quarter of the vote Hard or soft tops have more space at the top (this is a problem on the passenger side) but Touch Power Tops do not. Those who install JLs with Power Tops would need to lower the mount by about an inch (see image It was a necessity to shorten my Hello It was too low for my bmx, so I lifted it about 2" (picture 2).
I used two releasable cable zip ties to secure my bmx. I lowered the jack (pictures 3 and 4) and there is now no rattling even when driving off-road.

Azrael Cochran

| Jul 02, 2021

There are times when even the simple jobs end up a bit complicated, but not this one! The two plastic trim pieces need to be pulled. Mount a bracket with a few bolts on each side, and your high lift is ready to go! By the way, for the last step, all that's needed is a single bolt to secure the jack through a tab on the right, and a nut to secure it to a pre installed bolt to secure it to It looks fantastic from up there, I have to tell you! Haha, stock as always). As well as how it matches my fire extinguisher, I love the design. I would like to point out these two things According to the instructions, it is necessary to modify the plastic trim pieces after installation, which involves cutting through the plastic to accommodate the thickness of the bracket (which means the trim will not completely seat/be flush after installation). There is no doubt in my mind that you want to try The whole process took me no more than ten minutes Using the saw blade of a Leatherman's tool, it took about 15 minutes per side. Then I used a file to smooth it out So there is no way you would guess that the trim piece was modded! put any mods on it, you need to leave the plastic off entirely, since it is likely to fall off after the clips don't fully seat and the snap takes the plastic piece with it. Oh, and the second thing is that, depending on your jack, you should be able to lock it to the left side tab as well. This week, I was ecstatic to discover that I could use a standard-size padlock in the handle hole of my 48" black Hi Lift, as the hole adjacent to where the bolt enters lines up exactly with the one the bolt passes through. I hope you will take a look at it and consider buying it. It's very solid and of high quality, so easy to install that even a monkey could do it, and it looks fantastic (see pictures).

Paul Duke

| Sep 20, 2020

It's true. I highly recommend this jack for its ease of setup and mounting. There is however a chance of the jack rattling. zip tied and padded most of the parts, but the rattle continued. My next step was to go to Hobby Lobby where I got a huge foam square, cut it in half, and wedged it between the roof and jack. This time there was no The motorcycle will make a little noise when you hit enough bumps, but it is fairly silent for the most part.

Melvin McFarland

| Oct 17, 2020

I was really pleased to find this. In an ironic twist, I was told about it as I was looking for a way to hang my The fact that it is protected from the elements is a big plus for those who use their jack in a real way. It is not exposed to sunlight, there is no road spray, it is not wet. Whenever I need to use it, I can be sure it will be ready. I have to tighten it up enough that I need a socket or a multi-tool for it, as it's making a little rattling noise You can undo it by using a pliers.

Cynthia Oliver

| Sep 03, 2020

I knew exactly where to find what I needed. I am updating the review for this product and including the original review It would be a waste of money to add nuts to the list. A couple of days after waking up, they will get up and shake themselves loose. Buy some lock nuts for $2. They said it would take 2 weeks to arrive, which is fine, and it showed up express mail three days later. It only took 5 minutes to install. We used strong garden clippers to cut the existing plastic and install it back into place. This is a piece of cake. I like it a lot. I think I'm going to be satisfied. A 3M Rubber sheet will be used so it fits snug and does not rattle. We're excited about this product. We didn't want to mount it on the outside of the Jeep, and because it will be on the inside of the Jeep it will take no space that would have ever been utilized.

Callen Randolph

| Jun 11, 2021

I was nervous it might rattle or make noise, but it didn't make a sound. It looks great both in the rear view mirror and as well. It keeps my Jack out of the elements and is safe from the.

Connor METCALFE

| Jul 25, 2020

The plastic roll bar covers are easy to install, but I wish they had included a temple so that you could trace the area that needs to be cut. If there were anything to complain about, I would suggest that they provide a wing nut so that you can securely and unsecure the jack with only your hands and not be required to carry special sockets to do it. In general, a great buy since you won't have to expose the jack to elements and don't have to worry about locking it down to keep thieves out except if you don't have a hard top on your car.

Raiden Lawson

| Apr 09, 2021

As I understand, it is now custom to mount these outside in the open for everyone to see. However, you are exposing your lift to the elements, which will cause it to wear prematurely. You cannot imagine how beautiful this mountain is without knowing what its name is. You can use this mount to protect your lift, and it won't block your view out the backside. During installation, it took about 20 minutes to bolt it to the inner frame. While it came with detailed instructions, I had no need for them due to the simplicity of the installation. I haven't heard a rattling from the mount as it is very sturdy. In case you want to look cool, by all means mount the lift on the hood or wherever you want. You should get this mount if you are searching for a cost-effective solution that gives you protection for your investment and makes it easier to access your lift.

Rocco White

| Dec 20, 2020