Beech Lane Upgraded Toilet Water Valve Kit for Thetford Aqua Magic IV Toilets, Compare to Thetford Part 13168, High Performance in Freezing Conditions, Improved Valve Lifespan

The replacement I received looks to be an exact copy, and it was said it was made out It is not clear what the instructions are supposed to mean. In the report, they should offer advice on removing the rear screws on the underside of the rim which hold the rear cover in place, so the flush handle mechanism and spring can be accessed. To remove the link from the hole, one needs only to push the end of the spring enough away. It is then a simple matter to remove the two screws holding the valve in place and then to swap the link onto the new valve before it is installed. Replacing the link end into the handle mechanism after removing it. You can then reinstall the toilet gasket in your RV again and put your toilet back in.

Selena Kelley

| Feb 12, 2021

It is a good valve replacement kit for Beechline. Unlike many videos, there is not a great deal of information on how to replace the part correctly. So here are a few points you may not be aware of. I. *. Be sure the black o-ring at the valve top of the valve is in place prior to installation Located inside the top of the main valve body, the ring functions as a seal. Picture (See below). 3.
The most efficient way to replace an essential part is to get the toilet removed and the flush mechanism access panel (FMAP) removed from the top. allows access to the spring wire of the new flush valve that needs to be connected to the spring wire. A total of four screws hold the FMAP in place, so you'll need to remove them. 1.
2. The spring wire for the toilet must be unhooked with the FMAP removed. 3.
Make sure the correct end of the spring wire is inserted through the hole and through the valve arm before inserting the new valve. Then read on. Position the valve body for installation on the top of the toilet's rear wall. Feed the spring wire toward the flush lever as you do so. ** Note 6. Ensure that the valve body has been pushed into position. In an orange O-shaped box Fitting the valve into place will be easier thanks to the ring. The 7th point. Return the spring wire to the base of the flush lever (looks like a little wheel with a spring)
8. Use the screws included in the kit to connect the valve body to the toilet. The ninth point. Replace the 4 screws you removed with the ones you will use to attach the FMAP to the toilet. The number 10. (Replace the toilet seal on the bottom of the toilet, if necessary. Then you might as well do it)
11. To ensure the new valve is working properly, test the flush lever to make sure it is pulling the spring wire. The number 12. Please re-phrase The toilet will be mounted on the wall. You should hook up the water lines and test it all.

Malcolm McConnell

| Dec 11, 2020

It fit perfectly. It was not a problem at all. I found the camper store to be twice as expensive and took longer to get an RV. Using the part I had on hand, it took me 15 minutes to fix the issue and have the system All functions of the product are working properly. Voici a tip You should make sure to clean any sediment in the hole where the plunger moves and seals before you replace the old part. Ensure that the old rubber is removed from the Making sure the old gasket on bottom is removed and that the new ones are placed (the new ones should already be in the packaging). When replacing the toilet gasket, make sure to remove the old one and place the new gasket on the bottom of the toilet before reinstalling. Installing the seal to ensure good performance. For removing and installing toilet nuts, you need a 1/2" hex key. To compress the seal, have someone or yourself sit on the toilet while tightening down each side.

Chandler Robles

| Feb 04, 2021

It was the linkage that held me back from giving 5 stars to ease of installation. I removed the original or replacement piece, and I believe the product I replaced is better made. Due to various other leaks in the plumbing I have yet to repair, I have not tested the function. In general, I think the purchase is an excellent one. Even more so considering that it includes all the parts needed.

Kimberly Maloney

| Sep 03, 2020

I was able to get in without any problem. In this kit you will find a replacement bottom of potty seal that requires that you remove the unit in order to install it. Despite the fact that I had to remove the toilet, I still managed to replace the valve. In addition, the valve body was attached to the back of the potty with new screws. Since I just installed it, I am unable to comment on its durability.

Luke Dyer

| Sep 18, 2020

Since the Thetford was supposed to take one, I bought this There will be a 2-month wait for shipping. I made a bad decision. The leak started as soon as it was installed correctly. It was exactly the same as installing the Thetford replacement that I found from another seller. The seals are perfect and there are You can't go wrong with that - Keep your brand name and avoid getting knocked off The garbage has been taken off the street.

Aylin Gomez

| Dec 04, 2020

The valve can easily be changed and the toilet can be re-installed once the stopper is out. The latch is located on the back of our toilet, and there is no easy way to get to it.

Anya CHADWICK

| Jul 24, 2021

The Beech Lane Upgraded Toilet Water Valve Kit was purchased to replace my Thetford Aqua Magic IV Toilet, which is designed better and rated higher for freezing conditions than the Thetford. It was shipped quickly and arrived on time! It was properly packaged, well protected, This is a perfect replacement part that fits perfectly!.

Graham Montoya

| May 24, 2021