RVGUARD RV Screen Door Cross Bar Handle Adjustable from 21-5/8 Inch to 28-5/8 Inch with Sturdy and Secure Non-Slip Grip
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The cross bar can be adjusted from 21 to 35 inches wide depending on the width of the screen door. from 5/8 to 28- 5/8. Yes, if this is appropriate. I sincerely hope this information is useful.
We've got the Lippert solid step, and it's great.
Installing it is a breeze. A user manual is included in the package. It usually takes 15 to 30 minutes. It should take no more than 20 minutes. It'll be a perfect match for your screen door. Thank you very much!
The width of the screen door handle is approximately. It comes in a variety of lengths ranging from 21 to 25 inches. from 5/8 to 28- 5/8. I sincerely hope this information is useful. Thank y
Selected User Reviews For RVGUARD RV Screen Door Cross Bar Handle Adjustable from 21-5/8 Inch to 28-5/8 Inch with Sturdy and Secure Non-Slip Grip
I had no idea how much of a difference it would make, but it makes closing the door a lot easier. br>br>I deducted a star because there were no instructions, but it wasn't difficult to figure out. The self-tapping screws are supposed to be self-tapping. I didn't waste any time and just drilled pilot holes instead of tapping, but you'd need a gorilla grip to get them to bite. All I can say is that the wife is a lot happier now. A happy wife equals a happy life in the RV.
All good. Before making a purchase, I read other reviews. I took the disadvantages, learned from them, and installed it with no problems after dry fitting it first. Then, using a pencil, mark the pilot hole locations on the bar and the door for the two different types of screws. The aluminum was excessively long in our case. I hacked away at the excess with a hacksaw. After that, I drilled pilot holes on the left side and dry fitted it. Install screws in the bar/black handle section, then dry fit the entire bar and drill pilot holes in the right side. Finally, screw the more pointed screws into the door just enough to hold it in place; don't overdo it. Done and dusted.
However, for the installation, you'll need to be at the top of your DIY game. For best results, use your own mounting hardware instead of the included screws, which will break off with minimal torque if the holes aren't drilled to the exact correct size. br>br>There are no instructions included, despite the fact that each installation will be unique and will necessitate 12 precisely drilled holes. You're on your own when it comes to determining the exact screw location and drill size. br>br>Best of luck!.
W bought one of these for the 5th wheel we were living in a few years ago. We traded our RV for a new one, so we bought another bar and installed it in the same spot on the door as before. br>Because it's a little more difficult for me to reach the screen door from the ground, my husband suggested we get another new bar and hang it lower on the door as well. It works perfectly, and I appreciate the fact that there are two hand bars on the door.
Why aren't there any guidelines? I made educated guesses about the size of the drill holes that would be required. Fortunately, I had no problems installing them, but I noticed that some people complained that the cheap screws broke, which I can understand, especially if the drill size was incorrect. In retrospect, black screws to match the black plastic would have been preferable. br>br>After 12 screws, it appears to be sturdy enough. It appears that this could have been designed to be more easily assembled. Having a friend mark the holes for drilling when you level it is extremely helpful.
So I should have paid attention to the fact that it needed to be drilled in the first place. I was under the impression that it had been planned ahead of time. Anyway, the screw was so weak when I used the drill that the top part came off, and now I'm down a screw and it's wobbly. I went ahead and installed it anyway because I didn't want to deal with 1 screw.
My Casita's screen closes much more easily with the bar. To make it easier to unlatch the door, I had to use a cord to extend the handle over the top of the bar. With the aid of my Dremel cut off wheel and a drill, I was able to install it fairly quickly. Simply ensure that you measure and mark the door. On my door, at least, there isn't much leeway for error.
The majority of RV screen doors are awkward to open - It's a lot less difficult now. Because you need to do some fitting and drilling of the handle itself, installation was a little more difficult than with a similar product I bought a few years ago for an older camper, but I think that's a good thing because it means you can get a perfect fit. To me, it appears to be a well-made product.
Related Products For RVGUARD RV Screen Door Cross Bar Handle Adjustable from 21-5/8 Inch to 28-5/8 Inch with Sturdy and Secure Non-Slip Grip
