SPC Performance 81305 Camber Bolt

$ 21.37

Score By Feature

Based on 42 ratings

Easy to use

9.80

Scent

9.70

Value for money

9.70

OveReview Final Score

How Our Score Is Calculated

Product Description

The type of product is AUTO PARTS

China is the country of origin for this text

There is no weight to the package. This morning she weighed 61 pounds

11 inches in length by 11 inches wide by 11 inches high. There are 684 lines x 5 columns in this report. The dimension of the piece is 8" x 12". The area of 7 W is

Questions & Answers

What's the difference between a pair and a single ?

There are two of them The item covers the right and left sides of the front.

If there is any difference between this bolt and the 81260 bolt, what is it? In SPC's database, 81260 is the rear upper row, and this is the front lower row. And yet, both have 14mm holes. ?

An 81260 is used to adjust the camber in the rear. I am not sure if you could use it on It would be 14mm and the same length if the front camber bolt were 14mm and the There should be no reason why you cannot use it for the front of the book. You may only drop your scion frs 1 if you really don't need it. If you don't need camber bolts for the rear, you won't need them. I was able to achieve perfect alignment using SPSC lower arms alone.

Selected User Reviews For SPC Performance 81305 Camber Bolt

Crash bolts are mounted on top of these camber bolts, like how crashed bolts are

4/5

It was impossible to get past just these bolts There is a 1 degree camber on the driver's side. I thought to myself, what's up with that? My alignment at NTB got me narrower diameter bolts for the top hole (SPC Camber bolts were installed in the lower hole) and a wider brace for the bottom hole. - was what we dialed in These camber bolts and crash bolts are essentially the same thing at this point. It's quite likely that I did six or more track days before getting some camber plates, so the bolts came out, almost. There were problems with the bolt on the passenger side. It was a pleasure to work with a seasoned mechanic. I tried everything. There was a damn camber bolt in the SPC that would not Cut the bolt head with my sawzall so I would be able to pull that SOB out of my less than one year old car. The lesson learned here is to install bolts in accordance with specs. Getting the bolt stuck is not the fault of SPC. There is also no guarantee that you will get the camber you want because production vehicles have manufacturing tolerances. It has not been adjustable from the factory, so the caster of my wife's Jetta is not in whack.

Emelia Fuller

| Apr 21, 2021

The front end of your 1986 will look amazing with this camber solution! When you want to lower your BRZ/FRS/GT86, here is your solution! Using Swift 1" lowering springs, I was able to get low enough to fit in -/-* The front has a negative camber of 2 degrees

5/5

you can run without adjusting the rear end, but I could not run without it when I lowered my vehicle. I was surprised to see a dynamic of 3 degrees, especially for this vehicle. It is either the Whiteline camber adjustment bushings or SPC Lower Control arms I will be purchasing.

Clarissa Chaney

| Dec 15, 2020

Ensure that they are installed in the correct mounting holes on the lower side

5/5

You will need to install these in the correct lower mounting bolt holes, then install the bolt you removed into the upper mounting bolt hole (that will be the OE crash bolt) and then you can get the car back into position. An example of a two degree negative camber is.

Dominik Garner

| Dec 15, 2020

I give it five stars

5/5

Has been able to achieve the following results The camber is 2 degrees. I was happy with the results.

Frankie Shelton

| Feb 16, 2021

We give the film four stars

4/5

Does what needs to be done, not necessarily the most elegant thing.

Walker Gonzales

| Jan 28, 2021

Don't think about it

5/5

Just buy it. Installation is simple and it does exactly what it's supposed to do. Overall, I feel that I've earned the full 1 point. I look forward to 75 degrees. The corner grip is drastically different from the other grips.

Iyla Black

| Dec 22, 2020

This is not the kind of thing to do

3/5

There is a problem with the nut fitting metric or SAE sockets. A deep well socket is necessary to install the bolt since it is so long. nut's slightly tapered face gives it an easy grip and allows for easy stripping. It is garbage to throw away a part of such a specialty.