Shankly Oil Pressure Gauge Compression Tester - Mechanical Engine Compression Testing Kit
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
My recollection of it is hazy at best. As a consequence, if I do not have the correct adapter, I buy a second plug for the test hole, drill a small hole in it, then braze or TIG that plug to one of the fittings that I do not
The oil pressure sending unit/switch can be found in the oil tank. There is usually one on the passenger side of the engine block. Remove the coupler and screw in the correct thread adaptor, then connect the gauge. Start the engine, then press the button at the gauge until it begins to leak oil. Specific locations should be found in the vehicle repair manual
Having a bar pressure of 10 bars/140
You can use it with any car thanks to the adapters
Selected User Reviews For Shankly Oil Pressure Gauge Compression Tester - Mechanical Engine Compression Testing Kit
On a 3l flex fuel, my oil pressure sensor displayed very strange and erratic readings. Sometimes it measured 0 psi and sometimes it measured 80 psi. My oil pump was working properly, so I hooked up this gauge to see if there was a problem. The sensor was in an awkward position (I had to use a Lisle 13250 socket to get it out) so it took me about fifteen minutes to remove it. The old sensor needs to be removed and replaced with the mechanical gauge, taking about 20 minutes. As I looked at the mechanical gauge, I was able to clearly see what the problem was. Over time, the gauge began to leak oil from its connections between the rubber hose and the top of the gauge. Although I did not think this had any real impact on me, I'm worried that a gauge of this quality could break through the hose completely, causing oil to leak out, losing pressure, and damaging an engine. I returned the gauge to amazon because of this concern. This is not the kind of book I would recommend- A little more money will get you a better gauge of the extent of your project.
There is no way those bad auto part store gauges are not broken, they always have all the parts, and they are terrible to use. There was no doubt that this gauge was There are quite a few adapters included. That seems to be a very well made device. It was installed on a Jeep 4 that I had. I replaced the oil pressure sending unit on my 0. 0L engine to confirm that its oil pressure was too low. Adding this tool to my toolbox has been a good move.
(I use the #8 adapter most often. ) There are spare orings and an adaptor for 90 degrees included in the kit, and so far, there have been no leaks from the quicki connect couplers. I didn't have to spend a lot of money on a set from the tool truck, so it's freaking awesome! In a 2001 Volvo with a 2 liter engine, it did its job today. Engine with a low oil pressure complaint is a 4L turbo engine. This oil pressure gauge set is all you need if you want an oil pressure gauge set. This is a must-see movie. You won't regret it.
In addition to marking 1-10 on the valve fittings, there is no listing that indicates what thread size each marked number corresponds to. Some differences between M10 and 1/8 are obvious, but some may be more difficult to identify without the chart and could lead to thread damage in the fitting and engine if the wrong adaptor is used.
For the money, this is a great product. The program works well. It would have been nice to have a list of threaded adapter sizes included in the My Chevy Silverado is having a low oil pressure problem, which I bought this to test. Below 20 psi, the resolution just will not be good enough to achieve an accurate result. I would recommend this equipment to anyone else.
In addition to serving as a diagnostic tool, the device can also serve as an ultra-short-term monitor when modifications are made to assess any resulting I could think of only one improvement a brass cap that could be put on and left on the quick-disconnect to make it easier to take spot readings without having to remove it. If I had to buy it again, I would.
The link is not working. Pressure did not cause her to move. The product is new and has never been used, however it has so poor quality that it breaks quickly in the case after being put in its case. It was made available to me a few days after the return window closed, so I tried it for the first time then discovered they were useless.
I really love this thing. It is of great quality at such an affordable price. It appears to be a very well made product. Since I did not have anything to compare it with, it is impossible for me to evaluate the accuracy of this. It has a rubber bumper that well protects the gauge, and the hose is of decent length if it is routed properly back up in the engine bay. There is nothing to complain about. In 2005 5, it does what it is meant to do. In 4 l 3, you will find the following information.