* Disclaimer: OveReview is reader-supported. We earn commissions from qualifying purchases
MSD 3311 Spark Plug Wire Boot and Terminal, (Set of 2)

MSD 3311 Spark Plug Wire Boot and Terminal, (Set of 2)

MSD 3311 Spark Plug Wire Boot and Terminal, (Set of 2)
$ 11.42

Score By Feature

Based on 104 ratings
Value for money
8.88
Easy to install
8.52

OveReview Final Score

How Our Score Is Calculated

Product Description

The product has been designed to last
The property of being heat resistant
Protect your system against spark loss to the max
Providing dual crimp terminals with locking mechanisms

Questions & Answers

Wire number 5 is what I use for my paramotor. I can. It is five millimeters long. Could you please let me know if this is the right size to get or if I should find a smaller gauge size. does it simply screw into the ?

I have no issues with this for my Nitro 200 and the wire clamps on so no worries there either. Keep your eyes on the skies. It is a clear proposition.

My old boot won't come off without cutting the wire. How do I do that?

If they are not a non-slider, they should be shown the door Boots and wires made by the MAS brand. There's a possibility that you'll have to cut the boot off (since it may be permanently attached) if they're not MSD. The new boot can be slid on if the old one is still in good condition. Depending on the condition of the terminal, you may need to cut the wire (but you will need the crimp/strip tool), so you will need to do it nevertheless.

Is this going to fit an Could you please tell me if the wire is 5 mm?

I do have 8-inch feet and they fit me. Approximately 5mm thick. I had to use WD40 for sliding the cover

Are these tools compatible with the 212cc predator?

You can use these on nearly any spark plug size, yes. Using one for our tao tao ching chong quad was extremely handy.

Selected User Reviews For MSD 3311 Spark Plug Wire Boot and Terminal, (Set of 2)

You're too close together
3/5

I'm in way too much trouble! You're too close together. Getting the MSD wire through the boot is nearly impossible. Grease will not help you out on this one. You will have to figure it out on your own. In the event of too much effort, the boot will be torn. The reason they sell them in pairs probably has to do with that. MSD always has so many overpriced products, does it have to be that way?.

Leroy Cain
Leroy Cain
| Jan 31, 2021
There was a small piece that The plug for my paramotor is made of this
4/5

Compared to the factory supplied one on the Nitro 200, this one holds up better, however the small metal piece on top of the attachment point broke As it would be difficult to reattach it, I've been using it without that piece as it seems to hold up just fine without it.

Tori Bell
Tori Bell
| Sep 24, 2020
This is quality
5/5

My turbo manifold was so close to #3 spark plug that the rubber 90 degree boot melted and the spark voltage leaked to the manifold causing a misfire. Silicone has a much higher melting temperature so I will report later how well it works. I've had a good experience so far.

Kaliyah Vega
Kaliyah Vega
| Aug 25, 2020
Boots of the highest quality
5/5

You can use these boots on any power sport vehicle you need new boots for. the boots for snowmobiles and they perform better than the.

Salem Finley
Salem Finley
| May 01, 2021
A spark plug boot like this works perfectly for paramotors
5/5

It works great for paramotors to use the spark plug boot. The clip is attached to the plug end to prevent it from popping off while flying.

Kaydence Nicholson
Kaydence Nicholson
| Apr 22, 2021
This is a very well-crafted item
5/5

A high standard of The product made by MSD as usual is superb.

Jad Frank
Jad Frank
| Feb 18, 2021
They make a great replacement
5/5

The alternative to buying full sets of plug wires is not as good. It was a perfect solution.

Ivan Griffith
Ivan Griffith
| Apr 02, 2021
It is original and of good I found the quality to be excellent, but the price to be higher The set cannot be kept original if you do not choose another option
5/5

In order to train your hand, you need to spray silicone inside of the boot and, after connecting metal connector to the wire end, pull it slowly and gently by straightening out the angle as best as you can. That way, you're good to go.

Aron IQBAL
Aron IQBAL
| Jul 20, 2020

Related Products For MSD 3311 Spark Plug Wire Boot and Terminal, (Set of 2)