The harness for the replacement Fuel Injector Control Module (FICM) is shown below. Connecting your injectors to this harness will allow you to run your fuel injection system. The FICM module has been configured to work with the 0 Powerstroke diesel engine. With this wire harness you will find all the connectors you need. It is possible that your factory wiring has a short or loose connection when your truck displays injection fault codes, idles rough or runs rough. It should be replaced and you should get 6 instead. I've got a 0 horsepower Powerstroke running right now.
This is a compatible replacement for Ford vehicles The F250, F350, F450, F550, and Excursion models with the 6 do not fit the above parameters. Included under the 0 Powerstroke Diesel engine are model years 03, 04, 05, 06, 7.
The product replaces the part number This part replaces part numbers The 9D930-code The FICM injector wiring harness found on your F250, F350, F450, F550, or Excursion is not a genuine OEM part, but it is a direct replacement. The powerstroke The Super Duty has a 0 diesel engine.
The fit, finish, and quality of OEM parts. diesel fuel injector wiring harness features OEM connections to ensure an operational connection between the fuel injectors and the FICM. The wires throughout the system are made of high temperature material to ensure Wire harnesses are protected with a high-temperature wire loom installed in your F250, F350, F450, F550 or Excursion engine bay to protect them from heat and problems caused by engine heat.
We provide lifetime warranty on all our products A lifetime warranty is included with the diesel injector wire harness from FICM. When your wire harness, connectors, or pigtails break on your 6, you should contact your retailer immediately. If your engine is a 0 Powerstroke diesel, you may purchase a replacement from us.
Questions & Answers
Is it going to fit an 8/03 FFS- The number 350 is If 0, what does that mean?
My 2003 F350 had a 6-cylinder engine and I used it on it. I felt that it was the right All 6 would likely benefit from it, I think. The numbers 0 through 9.
What is the replacement for - The 12-b637- numeric code ?
There should be wires to replace from the ficm to the injectors if the wiring has to go from the ficm. It is not a number I remember, but it is the original wire
What is the replacement for - The 12-b637- numeric code ?
No, this harness is only intended for the ficm module and injectors.
The harness will fit a 6 inch belt. Engine model for the 0l powerstroke ford excursion? International/Navistar The 4nvxh06 symbol is used. AEB325 is the code. ?
Hello, this part will fit Ford Excursion 6 models manufactured from 2004 to 2005. This is L0L.
Selected User Reviews For FICM Engine Fuel Injector Complete Wire Harness - Replaces Part 5C3Z9D930A, 5C3Z-9D930-A - Compatible with Ford Vehicles F250 F350 F450 F550 - Powerstroke 6.0L Diesel - 2003-2007
On my 2003 F350 6, it was pretty simple to install. I had to take longer to remove my air filter than I expected More effort has been invested in removing and replacing FICM You can now install the new injector wiring The only issue I encountered was with the power harness to the FICM, since a release tab was broken, so I had to wrap zip ties around the FICM n the connector & install the adapter. The ficm bracket should be tightened up after the ficm is bolted to it so it doesn't move around & Power goes out when the ficm is used. When I turn on my truck, it starts and idles The system runs well! In regards to the small plastic locators that attached it to the intake studs, this harness was a little different from my factory harness, but I just ensured it was securely tied down with some zip ties, and that was the only problem I encountered.
| May 14, 2021
My harness made it possible for me to save The problem with a 6 may be caused by one of the following FICMs that run rough while cold should be replaced before you spend hundreds of dollars on a new one
According to my scan gauge, there are two, four, and five injectors I had 7 contribution/balance codes and on a hunch I replaced the old harness which was the original (16 years old) harness and now I only have one contribution/balance code for injector 5. I am pleased with the quality of this harness and how it fits. It would be best if a heat shield were added between the turbine and the turbo. My hypothesis is that the OEM harness was damaged by the excessive heat generated by the turbo.
| Jan 22, 2021
I would rate this product as great for the price
However, by no means is it comparable to the OE wiring harness due to its quality. The system works, however. Everything is going well so far. I paid much less for this than for what I would have paid from the dealer. Overall the purchase is well worth it. On my 2004 F250 6 I changed the oil. There are no powerstrokes.
| Mar 28, 2021
Do not purchase if you can spend an additional 80 dollars
A cloth cover was placed over the harness to protect it. Is that really the case? I wrapped it in foil tape where I thought it would need protection from high temperatures. It is likely that I will end up spending an additional 80$ and getting it from Ford when I need it for another project or to stud the heads, whichever is.
| Sep 22, 2020
A 2004 Excursion 6 should be able to fit
You can try it for 0L and see if There have been some issues with contribution and I've done a lot of fixes that have helped, but this was the final step. The contribution balance codes I was using are no longer valid. Thank you so much!.
| Dec 14, 2020
The key to a successful installation is your wiring harness! Those are my six
In a 0 powerstroke, the truck had been running fine for several hours, but then come to a stop light and started shaking and throwing All 8 injectors had their injection wiring hardness replaced from the FICM to the 8 injectors which took about 15 minutes. Every day is awesome now that the truck runs so well! You will need this part if your connectors are broken or you are missing the locking tabs on the FICM!.
| Feb 14, 2021
This harness is very nice
The fi harness I installed came with one injector plug that I had to pull off. It is evident from the gauges of the wires that this harness is smaller than the OEM So with that said, it works well. I like the neat assembly of the harness. It remains to be seen but for now, it gets 5 stars. We are really happy with the delivery. We ordered Saturday morning and received the order I don't have anything to complain about.
| Sep 09, 2020
I sent a message to resolve an issue, but did not receive a response
When I sent a message to resolve an issue, I never received a response. The part number matched what I needed for the truck I was working on, except it was pinned wrong, and I had to unpin it and redo the entire wiring harness to make sure it was right.
| Jan 13, 2021