Partsam High Mount Stop Light Third Brake Light Replacement for Silverado/Sierra C10 C/K 1500 2500 3500 1994 to 1999 LED Rear Cab Top Roof Center Mount Tail 3rd Brake Light Cargo Lamp (Clear Lens)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The backing of the item is a medium-soft plastic. A gasket isn't included with the product. My old gasket was going to be used or I was going to fabricate one from scratch. It is imperative that you cut the yellow wire or else the brake light will remain As far as I am concerned, mine is a totally awesome product that I would buy again in a heartbeat!
The interior lights are only on if I am in need of them, but I usually keep them off
There was only one thing I needed to redo, and that was the gasket.
Due to the fact that it is a piece of junk, the screen stays on all the time.... I think it's a total waste of time. Your money will be returned to you. This item is a waste of money and should not be purchased.
Selected User Reviews For Partsam High Mount Stop Light Third Brake Light Replacement for Silverado/Sierra C10 C/K 1500 2500 3500 1994 to 1999 LED Rear Cab Top Roof Center Mount Tail 3rd Brake Light Cargo Lamp (Clear Lens)
Although I was playing around with the wires and combinations, the picture resembles that of a jigsaw puzzle. I find this method to be very effective A tan and a gray-colored truck adorns my garage Several wires are white or creamish, one is black, and one is blue and white. As an example of matching the wires, here is what I did In addition to black and yellow lights, we have lights blue and white that connect to a Truck's white, lights red that connect to one of the Truck's tans (we didn't have to cut the wire when everyone else did)
It took me several tries to figure out which wire worked (I had to experiment)** The tan/white wire from the other truck was not used at all**In my research I discovered that the wires are set up as follows The black color is for the ground, the red is for brake lights, and the white is for reverse or cargo. The yellow color is the running light. I did not experience any problems with the lights. The brake lights come on even when the cargo switch is not on, and when I turn the cargo switch on, the two light LEDs come on on the ends, along with the brake lamp when I press the button. I suppose it's fine with me, however, that the reverse lights don't come on. As far as I can tell, the wiring harness on my truck does not appear to have reverse lights, so I do not think it's the product's fault (I may be mistaken). I have not had any adverse effects or shorted any fuses as a result of it. A few weeks after writing this review, I will make an update. It will hopefully be of some help! A brief update It is now late December and I have not had any issues with it. So far, there have not been any leaks. It works as advertised. It would be nice if it were brighter, but it's better than it not being I have definitely had a lot of rain and it's always been humid, but I haven't seen any fog. Nonetheless, I put silicone around the light to keep moisture out, so that's probably something that may have contributed.
In the same way as The only reason for two stars is that I had to cut the plug and hardwire. I found shrink wrapping the smaller wires easiest however, I had to cut the plug. There is no need for this since it is required I expect the plug to be a simple swap with the existing one in the Chevy Silverado. The K1500 I have is a 1994 model. It will be hard to test its watertightness for a thin soft plastic backing would have been a better option to seal as it is thin and not playable compared to For those who don't have a washer, you can use o-rings A ring must be attached to the screws in order to prevent the case from cracking. As the head of the screws on the old light has a wider washer-type head, I used those two screws from it. If you want to make the circuit work properly, you must do the following The color of black is light.
Wir have been playing around with a variety of wiring combinations that did not make any sense and have finally This is the combination used to make the third brake/cargo light work on my 1994 Chevrolet C1500. To light's red, truck yellow* To light's black, truck black * To light's yellow, truck black* To light's white, truck red* To light's red, truck yellow* To light's white, truck red.
It was not possible to connect the two connectors enough for them to click into place since the fit was so tight. In addition, I had to bend the electrical prongs on the male side to fit properly because they didn't line up exactly, but close enough so I wasn't forced to splice Since the plastic is brittle, I was worried I would break it if I didn't be careful when screwing it in, but it didn't break. Brighter and faster than original incandescent bulbs, the LED bulbs have all the benefits of conventional incandescent The led bulbs are now installed, and I hope they last for a long time. Would be nice to have a gasket included, as I repurposed.
There are a lot of gaps around it on a 1994 C1500. He had to silicone the earmuffs to get them out. It seemed as if the wiring was incorrect. A new harness was needed and rewired colors were corrected to ensure the system worked. I was disappointed in the While I would like to return, since I had to modify the harness to fit the right wire, I will not be able to return. We were lucky that the cost was not too high.
I purchased this for my 1994 Chevy Dual Cab. The smoked version was served to us. The yellow wire on the right had to be cut like others, but it was very easy to Would have preferred it come with new screws, but it's easily repaired. I'm really pleased with how everything turned out.
However, the electrical connector on the 1998 Chevy was not compatible with the one on the 2000 Ford.
It looks very This is a very good product. It looks very I used a wire cutter to cut the yellow wire from the light plug, so it would not stay on after I closed and opened the door. We would buy from them.