Upgr8 Universal Inner Diameter High Performance 5 Feet Length Silicone Vacuum Hose Line (3MM(1/8 Inch), Black)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
As far as I know, Mazda Miata hoses come in several sizes, but I bought several types to replace the ones in my turbo-passat. In any case, it held up well and the blue hose is useful to keep track of the ones you've
The same applies even in this case. The diameter of a hose can change depending on the model year, so it's best to remove one It's only speculation if you do anything else. Make sure you take the time and effort to do so.
It was very good
Using tape, you can increase the diameter of the plastic tubes if they turn out to be too large.
Selected User Reviews For Upgr8 Universal Inner Diameter High Performance 5 Feet Length Silicone Vacuum Hose Line (3MM(1/8 Inch), Black)
Because this hose was cheap as well as, let's be honest, it is the same as the rest, I used it to rebuild the vacuum system on my V8 swapped Audi A4. Some have called what some might call a cramped and hot engine bay, the place where it has been held up for months. Currently, I'm buying more in case I need it in the future for any other projects or.
To begin, I want to address the "Min temperature" of the hose The temperature was 40 degrees Celsius. This is the maximum temperature allowed. I am at 220 degrees Celsius/428 degrees Fahrenheit. What other web sites can you refer me to for this type of specification? That's a stellar set of My hose is really nice, thick, allows for some bends but it will not close on itself. Since it is stretching it will not get frail and crack. I bought some 3mm and 4mm (didn't use the 5% discount though (bah). To begin with, I must agree that the hose is really nice. I will now proceed to the seller (other than Amazon, their supplier I guess) and give them a thumbs 2), even if you get lucky and get the full 5', you still have to cut 1/8-inch off the ends (otherwise, it is fraud). But even if you do get lucky, and get the full 5', I would still recommend that you do that. The 1/8" must be cut off to get a clean edge, and if you must do that on both sides, then you bought a usable 5' and if the ends are cut at an angle or otherwise, it is not a usable 5'. As a result, this issue needs to be rectified as soon as possible. Though the hose is made of good quality, it does not last long. I also encourage you to charge less per hose if you keep your UGR8 diecast sticker. Instead of sending me these UPGR8 tin pieces, maybe you would like to switch to a tiny sticker so I can keep the tin for the bigger hose I have no need for them, so stop sending them and reduce the price!.
Hose is able to perform to expectations. The coolant overflow tube was installed and installed as part of the cooling system. The problem has been resolved. I received my package without damage on time. This was a product I would buy again if I needed more for a project.
Due to its thickness, I used hose clamps designed for 7/16", 3/4" and 3/8". The diameter of the hole is 1/2". Using hoses. This type of device does not cut into hoses as often as worm gears do. Here are some pictures.
There's no point to this stuff. The bridge collapsed at 0 The 27th inch of mercury.
Measurements Diameter of the outside ring Is 9mm thick. A * Length A height of 5 feet (60 inches). The thickness of your walls is Three million. Although the outside diameter is about 7, the actual inside diameter is 3. In my application I need at least 9mm, but that is too small. My turbo blow off valve application required that I order the 9mm size to fit the special steel clamps I ordered. Returned to a different vendor and will purchase from them in the future. The UPGR8 item size will hopefully be listed once they get their act together.
In keeping with my 2004 Saab, I bought these to replace all of its vacuum lines. This product made a huge difference in the performance of my car since there were no more leaks in the vacuum lines. There is only one complaint I have, and it is that the amount of 5 feet was There should at least be ten feet between the two. In order to replace your line, I recommend that you purchase at least two or three packages. Having too much is always better than having too little. To get it mailed to you, it needs a couple of days.
Initially, I was concerned about ordering this particular style of vacuum line since I'm used to the rubbery stuff you usually get from the parts store. Yet, it turned out to be exactly what I needed. There is no doubt that this product is Cutting was easy with a razor blade, and routing through the engine bay was quick and easy. I could not detect any leaks in the vacuum connection. A recommendation for this product would be appropriate.
The pros are The hose is a little short the cons are * Poor tolerances* * Poor description
The bag on the shoe is sealed, and the shoe is black as described. Low psi vacuum cleaners can use the flimsy vacuum hose. When I went to test fit it on a 3/8 coupling, it was very loose around the coupling, so I took out my calipers to find the internal diameter and discovered it is I have the calipers set to 409 inches on the inside. You can see the reading in the picture. To show how much of a gap there is in a 3/8 pipe, measure 375 inches. The next question is "Is this ok for pipe 10mm in diameter? ", but the answer is no because the pipe size is so large it's The hose is way too large and has too many tolerances. If the tolerances were smaller, it would be acceptable.
Related Products For Upgr8 Universal Inner Diameter High Performance 5 Feet Length Silicone Vacuum Hose Line (3MM(1/8 Inch), Black)
