High Performance Silicone Vacuum Hose - 10 feet - 1/2" ID (.5"|13mm) - Black
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
A working pressure of 62 psi is required. The burst pressure is 185 pounds per square inch
You should be able to use it without any problems.
This is about 10', more than enough to do all of the vacuum lines on my car with more
Neither I nor BMW know anything about it. In the Kawasaki J motor, I used the stuff I bought to create a vacuum line. A vacuum line runs from the valve cover to the 4 carburetors and vacuum controlled fuel petcock on top of the valve cover. Despite high temperatures and traffic jams on interstate and the lines are good at this time, air conditioning is still purchased/installed in 2016 with no *deterioration* occurring. The air is over 100 degrees and there are 30 minute traffic jams on the interstate. Black is the color of the line I received. A variety of sizes were available for the line. 3/8" outside diameter is the outside diameter of the line I got Approximately 5mm thick. A diameter of 3/16" is provided on the inside About 5 cm. There are two millimeters of thickness in the line wall. A finger can be squeezed around the cut end of the line since it is firm but still flexible.
Selected User Reviews For High Performance Silicone Vacuum Hose - 10 feet - 1/2" ID (.5"|13mm) - Black
are being replaced. Here is a list of products that I am in the process of replacing. As soon as the intake manifold was removed, the vacuum hoses became extremely brittle. In my initial thinking, I was going to get the hoses from my local auto parts store, but after reading that they are very poor quality in terms of heat resistance, I decided against doing so. Thanks to NXS, I came across this product. It was my pleasure to purchase the three. There is a 5mm difference in every 10 feet. It was evident, as soon as it was installed, that it was superior to the stock vacuum hose. Even though the stock hoses came in a variety of sizes, I was able to replace them all with this one size. According to the description, the walls are thicker and the room is good for heating. There is no difficulty in cutting the hoses. My only tool was pliers that cut to the side. A lot of the blue color really stands out as well. The next time I buy from NXS, I will buy more!.
A very dense and durable material. It will be used with air testing equipment and has a 3/16" ID. The material is incredibly flexible for its thickness and works wonderfully. In testing instruments, 1/1000th of an inch per vacuum chamber is measured, so they must be durable and not prone to cracking. There is only one thing wrong with it, and that is that I wish the silicone content were a little higher so it could flex even more. Here is a picture of how thick and nice I am updating the 7/2019 update to include The item is still working perfectly, even when it is placed in an industrial environment, where it is connected and disconnected from hose barbed test equipment, it still holds up as well as it did when it was brand Flexibility has not been lost. This hose is heavy as well as more cumbersome than neoprene, but it is.
This is an excellent replacement for rigid vacuum lines that have cracked under the hood from age and abuse. You will have to make sure that this does not rub off on I used this material for my customary wooden hat, and it is very soft, cuts very easily, and can handle high temperatures well. There may be a way to slip a High temp sleeve over this stuff as well to protect it a little better from any any My Audi Q7 had a large amount of vacuum tubing that needed to be replaced, and I used this product. I didn't have to buy $300 worth of pre-owned cars Tubes made of plastic bent into a 90-degree angle. It is ready to go. I just had to reuse the fittings on the hard line on the flexible line.
This looks to be a very good product. A good tie wrap will certainly outlast a tie wrap that you might use to close off the hose. The BMW hoses burned before this silicon did in a burn test. It is easy to install and trim. If you must go around narrow spaces, the material is flexible enough not to pinch.
I replaced all vacuum hoses on a 335i N54 engine. They were much longer than 10 feet.
It was ordered so that I can make brake savers for my motorcycle off-roading adventures. 3/32 braided steel wire is inserted into the tubing. It is then looped around the frame, swaged, and then swung to the brake and clutch pedal ends. The frame loop on my new bikes is close to the engine, so instead of using vinyl tubing that is traditionally used, I wanted something that would do well in the heat. Contact was made with the seller and the seller was very helpful and assured me that it was a tough process. The two of us are 100% in agreement. My project could not be more perfect. I would like to use some of the larger inner diameter tubing on the bike as a wiring conduit for the aux lights which are going to run along the frame and.
I have replaced the vacuum part on my Color contrasts nicely with the fit and fit. My interior is a good match!.
The color is Although I would have liked to have given this product 5 stars, the color of the tubing is dull and more discolored than the picture depicts, which is kind of surprising since I have currently used other vacuum lines that are the same color as the product It is generally a good-quality tubing with a thick wall.
It has been a while since I purchased their silicon vacuum lines but here we are. Although they are the same price, they do not have the same quality. Quality will change with heat but I am unsure how well they will hold up for my N54.